Do you want this big green box to go away? Well here's how...

Click here for full update

Wildcat! photo archives restored.

Click here for full update

Donors can now disable ads.

Click here for instructions

Add yourself to the user map.

Click here for instructions

SR3500 Fus-409/Pulley BB-128

Converted from Wildcat! database. (read only)
Locked
Wayne G. O'Shea

SR3500 Fus-409/Pulley BB-128

Post by Wayne G. O'Shea » Fri Feb 17, 2012 9:38 pm

Hi guys and gals!

Now for something totally different! I have a question for you SR builders,
that I would like some replies to! Looks like it's time for me to get some
list usage the other way, with this new project underway!

I am sorting out all the stuff that is done and still needs to be done to
this SR2500/3500 I have come to own, so I can start "tearing" into it.
Before I go drilling those big 1/2" cable clearance holes through the fins
front attach bracket (scary looking stuff aye!) I have noticed that the two
BB-128 pulleys that are mounted to the Fus-409 brackets are so big in
diameter that the previous builder had to shim the brackets out from the
bulkhead for the pulleys to clear it enough to roll and that the predrilled
cotter pin (cable retainer) holes are not useable. There is not enough
material, out far enough, to drill new cotter holes. I think I remember
seeing a note from Elaine in shipping about a change in pulley diameters
from old stock to new stock that may have been addressing this, but I can't
find it. What have those of you that are beyond this point ran into here??
Change of pulleys, mfg new brackets, extend the top bracket tab with a
couple add ons to allow for a new cotter hole, or ??.

Thanks,
Wayne G. O'Shea
Sasquatch #017
..... and many, many Rebels!
www.irishfield.on.ca





-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
Top
Al & Deb Paxhia

SR3500 Fus-409/Pulley BB-128

Post by Al & Deb Paxhia » Fri Feb 17, 2012 9:38 pm

Hi Wayne,
Well as I best remember, the folks at MAM said they discontinued the smaller
pulley and I was short one. Then I received a larger FUS409 bracket and
larger pulleys, the larger bracket and pulleys did not align with the hole
in the fin. I used the original smaller 409 and ordered a smaller pulley
from Aircraft Spruce. All went together OK we will see how it works.
Al
SR#26
----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <murphy-rebel@dcsol.com>
Sent: Monday, January 14, 2002 6:15 PM
Subject: SR3500 Fus-409/Pulley BB-128

Hi guys and gals!

Now for something totally different! I have a question for you SR
builders,
that I would like some replies to! Looks like it's time for me to get some
list usage the other way, with this new project underway!

I am sorting out all the stuff that is done and still needs to be done to
this SR2500/3500 I have come to own, so I can start "tearing" into it.
Before I go drilling those big 1/2" cable clearance holes through the fins
front attach bracket (scary looking stuff aye!) I have noticed that the
two
BB-128 pulleys that are mounted to the Fus-409 brackets are so big in
diameter that the previous builder had to shim the brackets out from the
bulkhead for the pulleys to clear it enough to roll and that the
predrilled
cotter pin (cable retainer) holes are not useable. There is not enough
material, out far enough, to drill new cotter holes. I think I remember
seeing a note from Elaine in shipping about a change in pulley diameters
from old stock to new stock that may have been addressing this, but I
can't
find it. What have those of you that are beyond this point ran into here??
Change of pulleys, mfg new brackets, extend the top bracket tab with a
couple add ons to allow for a new cotter hole, or ??.

Thanks,
Wayne G. O'Shea
Sasquatch #017
..... and many, many Rebels!
www.irishfield.on.ca



** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
Top
Wayne G. O'Shea

SR3500 Fus-409/Pulley BB-128

Post by Wayne G. O'Shea » Fri Feb 17, 2012 9:38 pm

Al, thanks! That is what I figured and maybe I should dig a little harder
through all the boxes and see if there is another set of FUS-409's here. I
don't think there are though, so I will check through my pulley stock in my
NOS stuff and see if I have some with a smaller O.D. so I can use the cotter
hole and a similar 1.9" cable groove diameter so no extra stress on the
cables. I noticed that these BB-128 pulleys have a really deep side wall, so
there must be a pulley with a smaller O.D and the same cable groove
diameter. Just don't want to drill those 1/2" holes through the fin attach
at the current location and then change pulleys and have to make them into
slots!

Wayne G. O'Shea
www.irishfield.on.ca


----- Original Message -----
From: "Al & Deb Paxhia" <paxhia2@attbi.com>
To: <murphy-rebel@dcsol.com>
Sent: Monday, January 14, 2002 10:34 PM
Subject: Re: SR3500 Fus-409/Pulley BB-128

Hi Wayne,
Well as I best remember, the folks at MAM said they discontinued the
smaller
pulley and I was short one. Then I received a larger FUS409 bracket and
larger pulleys, the larger bracket and pulleys did not align with the hole
in the fin. I used the original smaller 409 and ordered a smaller pulley
from Aircraft Spruce. All went together OK we will see how it works.
Al
SR#26
----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <murphy-rebel@dcsol.com>
Sent: Monday, January 14, 2002 6:15 PM
Subject: SR3500 Fus-409/Pulley BB-128

Hi guys and gals!

Now for something totally different! I have a question for you SR
builders,
that I would like some replies to! Looks like it's time for me to get
some
list usage the other way, with this new project underway!

I am sorting out all the stuff that is done and still needs to be done
to
this SR2500/3500 I have come to own, so I can start "tearing" into it.
Before I go drilling those big 1/2" cable clearance holes through the
fins
front attach bracket (scary looking stuff aye!) I have noticed that the
two
BB-128 pulleys that are mounted to the Fus-409 brackets are so big in
diameter that the previous builder had to shim the brackets out from the
bulkhead for the pulleys to clear it enough to roll and that the
predrilled
cotter pin (cable retainer) holes are not useable. There is not enough
material, out far enough, to drill new cotter holes. I think I remember
seeing a note from Elaine in shipping about a change in pulley diameters
from old stock to new stock that may have been addressing this, but I
can't
find it. What have those of you that are beyond this point ran into
here??
Change of pulleys, mfg new brackets, extend the top bracket tab with a
couple add ons to allow for a new cotter hole, or ??.

Thanks,
Wayne G. O'Shea
Sasquatch #017
..... and many, many Rebels!
www.irishfield.on.ca



** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**


** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
Top
Mike Kimball

SR3500 Fus-409/Pulley BB-128

Post by Mike Kimball » Fri Feb 17, 2012 9:38 pm

This surprises me because I have serial number 44 which I bought almost 5
years ago from MAM which is a pretty early kit and I had no trouble at all.
The brackets, pulleys, hole alignment all worked fine.

Mike Kimball
SR#044

-----Original Message-----
From: murphy-rebel@dcsol.com [mailto:murphy-rebel@dcsol.com]On Behalf Of
Wayne G. O'Shea
Sent: Monday, January 14, 2002 6:52 PM
To: murphy-rebel@dcsol.com
Subject: Re: SR3500 Fus-409/Pulley BB-128


Al, thanks! That is what I figured and maybe I should dig a little harder
through all the boxes and see if there is another set of FUS-409's here. I
don't think there are though, so I will check through my pulley stock in my
NOS stuff and see if I have some with a smaller O.D. so I can use the cotter
hole and a similar 1.9" cable groove diameter so no extra stress on the
cables. I noticed that these BB-128 pulleys have a really deep side wall, so
there must be a pulley with a smaller O.D and the same cable groove
diameter. Just don't want to drill those 1/2" holes through the fin attach
at the current location and then change pulleys and have to make them into
slots!

Wayne G. O'Shea
www.irishfield.on.ca


----- Original Message -----
From: "Al & Deb Paxhia" <paxhia2@attbi.com>
To: <murphy-rebel@dcsol.com>
Sent: Monday, January 14, 2002 10:34 PM
Subject: Re: SR3500 Fus-409/Pulley BB-128

Hi Wayne,
Well as I best remember, the folks at MAM said they discontinued the
smaller
pulley and I was short one. Then I received a larger FUS409 bracket and
larger pulleys, the larger bracket and pulleys did not align with the hole
in the fin. I used the original smaller 409 and ordered a smaller pulley
from Aircraft Spruce. All went together OK we will see how it works.
Al
SR#26
----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <murphy-rebel@dcsol.com>
Sent: Monday, January 14, 2002 6:15 PM
Subject: SR3500 Fus-409/Pulley BB-128

Hi guys and gals!

Now for something totally different! I have a question for you SR
builders,
that I would like some replies to! Looks like it's time for me to get
some
list usage the other way, with this new project underway!

I am sorting out all the stuff that is done and still needs to be done
to
this SR2500/3500 I have come to own, so I can start "tearing" into it.
Before I go drilling those big 1/2" cable clearance holes through the
fins
front attach bracket (scary looking stuff aye!) I have noticed that the
two
BB-128 pulleys that are mounted to the Fus-409 brackets are so big in
diameter that the previous builder had to shim the brackets out from the
bulkhead for the pulleys to clear it enough to roll and that the
predrilled
cotter pin (cable retainer) holes are not useable. There is not enough
material, out far enough, to drill new cotter holes. I think I remember
seeing a note from Elaine in shipping about a change in pulley diameters
from old stock to new stock that may have been addressing this, but I
can't
find it. What have those of you that are beyond this point ran into
here??
Change of pulleys, mfg new brackets, extend the top bracket tab with a
couple add ons to allow for a new cotter hole, or ??.

Thanks,
Wayne G. O'Shea
Sasquatch #017
..... and many, many Rebels!
www.irishfield.on.ca



** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**


** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**


** To unsubscribe, send e-mail to list-server@dcsol.com with **
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself **
** Archives located at http://rebel:builder@www.dcsol.com:81/default.htm **
** To contact the list admin, e-mail mike.davis@dcsol.com **




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
Top
capete

SR3500 Fus-409/Pulley BB-128

Post by capete » Fri Feb 17, 2012 9:38 pm

Wayne,

According to our manual (circa 21/06/99) and shipping list,
we are to use the BB-128, which we have listed as MS24566-3B on shipping
list, with the FUS 409 brackets We put everything together without any
problems and our holes for the cotter pin (cable retainer) have enough
clearance.

And of course, if this has changed in latest manuals we have not heard about
it...

P & M
SR003

Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <murphy-rebel@dcsol.com>
Sent: Monday, January 14, 2002 9:15 PM
Subject: SR3500 Fus-409/Pulley BB-128

Hi guys and gals!

Now for something totally different! I have a question for you SR
builders,
that I would like some replies to! Looks like it's time for me to get some
list usage the other way, with this new project underway!

I am sorting out all the stuff that is done and still needs to be done to
this SR2500/3500 I have come to own, so I can start "tearing" into it.
Before I go drilling those big 1/2" cable clearance holes through the fins
front attach bracket (scary looking stuff aye!) I have noticed that the
two
BB-128 pulleys that are mounted to the Fus-409 brackets are so big in
diameter that the previous builder had to shim the brackets out from the
bulkhead for the pulleys to clear it enough to roll and that the
predrilled
cotter pin (cable retainer) holes are not useable. There is not enough
material, out far enough, to drill new cotter holes. I think I remember
seeing a note from Elaine in shipping about a change in pulley diameters
from old stock to new stock that may have been addressing this, but I
can't
find it. What have those of you that are beyond this point ran into here??
Change of pulleys, mfg new brackets, extend the top bracket tab with a
couple add ons to allow for a new cotter hole, or ??.

Thanks,
Wayne G. O'Shea
Sasquatch #017
..... and many, many Rebels!
www.irishfield.on.ca



** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
Top
Wayne G. O'Shea

SR3500 Fus-409/Pulley BB-128

Post by Wayne G. O'Shea » Fri Feb 17, 2012 9:38 pm

Thanks guys and Monica!

Making sense now by the serial number "range". The packing slip spells out
BB-128's which are 1.9" diameter at the cable and 2.5" overall, but
Peter/Monica's early kit #003 was shipped with MS24566-3B's that are only
1.5" at the cable and 2" overall. The kit I have (that was Dr. Rob Helt's)
is serial #17 and it was shipped with the BB-128's and the older smaller
Fus-409's. I guess somewhere in there people tipped off MAM and they started
making larger Fus-409's to go with the larger diameter BB-128's. I guess Rob
never asked for the new Fus-409's, as I don't see them here, so I will make
my own up and stay with the larger pulley for less cable stress.

Regards,
Wayne G. O'Shea
www.irishfield.on.ca

----- Original Message -----
From: <capete@golden.net>
To: <murphy-rebel@dcsol.com>
Sent: Tuesday, January 15, 2002 3:56 PM
Subject: Re: SR3500 Fus-409/Pulley BB-128

Wayne,

According to our manual (circa 21/06/99) and shipping list,
we are to use the BB-128, which we have listed as MS24566-3B on shipping
list, with the FUS 409 brackets We put everything together without any
problems and our holes for the cotter pin (cable retainer) have enough
clearance.

And of course, if this has changed in latest manuals we have not heard
about
it...

P & M
SR003

Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <murphy-rebel@dcsol.com>
Sent: Monday, January 14, 2002 9:15 PM
Subject: SR3500 Fus-409/Pulley BB-128

Hi guys and gals!

Now for something totally different! I have a question for you SR
builders,
that I would like some replies to! Looks like it's time for me to get
some
list usage the other way, with this new project underway!

I am sorting out all the stuff that is done and still needs to be done
to
this SR2500/3500 I have come to own, so I can start "tearing" into it.
Before I go drilling those big 1/2" cable clearance holes through the
fins
front attach bracket (scary looking stuff aye!) I have noticed that the
two
BB-128 pulleys that are mounted to the Fus-409 brackets are so big in
diameter that the previous builder had to shim the brackets out from the
bulkhead for the pulleys to clear it enough to roll and that the
predrilled
cotter pin (cable retainer) holes are not useable. There is not enough
material, out far enough, to drill new cotter holes. I think I remember
seeing a note from Elaine in shipping about a change in pulley diameters
from old stock to new stock that may have been addressing this, but I
can't
find it. What have those of you that are beyond this point ran into
here??
Change of pulleys, mfg new brackets, extend the top bracket tab with a
couple add ons to allow for a new cotter hole, or ??.

Thanks,
Wayne G. O'Shea
Sasquatch #017
..... and many, many Rebels!
www.irishfield.on.ca



** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**


** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
Top
Don Cormack

SR3500 Fus-409/Pulley BB-128

Post by Don Cormack » Fri Feb 17, 2012 9:38 pm

I have SR 087. My pulleys are of the larger diameter and require either a
larger bracket or a shim. I haven't yet actually mounted my pulleys. So I may
look for smaller ones, to avoid extra holes in the fin mount.

Don

On Tue, 15 Jan 2002 11:07:32 -0900 Mike Kimball <mkimball@gci.net> wrote:
This surprises me because I have serial number 44 which I bought almost 5
years ago from MAM which is a pretty early kit and I had no trouble at all.
The brackets, pulleys, hole alignment all worked fine.

Mike Kimball
SR#044

-----Original Message-----
From: murphy-rebel@dcsol.com [mailto:murphy-rebel@dcsol.com]On Behalf Of
Wayne G. O'Shea
Sent: Monday, January 14, 2002 6:52 PM
To: murphy-rebel@dcsol.com
Subject: Re: SR3500 Fus-409/Pulley BB-128


Al, thanks! That is what I figured and maybe I should dig a little harder
through all the boxes and see if there is another set of FUS-409's here. I
don't think there are though, so I will check through my pulley stock in my
NOS stuff and see if I have some with a smaller O.D. so I can use the cotter
hole and a similar 1.9" cable groove diameter so no extra stress on the
cables. I noticed that these BB-128 pulleys have a really deep side wall, so
there must be a pulley with a smaller O.D and the same cable groove
diameter. Just don't want to drill those 1/2" holes through the fin attach
at the current location and then change pulleys and have to make them into
slots!

Wayne G. O'Shea
www.irishfield.on.ca


----- Original Message -----
From: "Al & Deb Paxhia" <paxhia2@attbi.com>
To: <murphy-rebel@dcsol.com>
Sent: Monday, January 14, 2002 10:34 PM
Subject: Re: SR3500 Fus-409/Pulley BB-128

Hi Wayne,
Well as I best remember, the folks at MAM said they discontinued the
smaller
pulley and I was short one. Then I received a larger FUS409 bracket and
larger pulleys, the larger bracket and pulleys did not align with the hole
in the fin. I used the original smaller 409 and ordered a smaller pulley
from Aircraft Spruce. All went together OK we will see how it works.
Al
SR#26
----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <murphy-rebel@dcsol.com>
Sent: Monday, January 14, 2002 6:15 PM
Subject: SR3500 Fus-409/Pulley BB-128

Hi guys and gals!

Now for something totally different! I have a question for you SR
builders,
that I would like some replies to! Looks like it's time for me to get
some
list usage the other way, with this new project underway!

I am sorting out all the stuff that is done and still needs to be done
to
this SR2500/3500 I have come to own, so I can start "tearing" into it.
Before I go drilling those big 1/2" cable clearance holes through the
fins
front attach bracket (scary looking stuff aye!) I have noticed that the
two
BB-128 pulleys that are mounted to the Fus-409 brackets are so big in
diameter that the previous builder had to shim the brackets out from the
bulkhead for the pulleys to clear it enough to roll and that the
predrilled
cotter pin (cable retainer) holes are not useable. There is not enough
material, out far enough, to drill new cotter holes. I think I remember
seeing a note from Elaine in shipping about a change in pulley diameters
from old stock to new stock that may have been addressing this, but I
can't
find it. What have those of you that are beyond this point ran into
here??
Change of pulleys, mfg new brackets, extend the top bracket tab with a
couple add ons to allow for a new cotter hole, or ??.

Thanks,
Wayne G. O'Shea
Sasquatch #017
..... and many, many Rebels!
www.irishfield.on.ca



** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**


** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**


** To unsubscribe, send e-mail to list-server@dcsol.com with **
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself **
** Archives located at http://rebel:builder@www.dcsol.com:81/default.htm **
** To contact the list admin, e-mail mike.davis@dcsol.com **


** To unsubscribe, send e-mail to list-server@dcsol.com with **
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself **
** Archives located at http://rebel:builder@www.dcsol.com:81/default.htm **
** To contact the list admin, e-mail mike.davis@dcsol.com **
----------------------
Donald E. Cormack
Vice Dean,
School of Graduate Studies, and
Professor of Chemical Engineering
65 St. George Street
University of Toronto
Toronto, Canada M5S 2Z9
Tel: (416)978-2384 FAX: (416)978-1649
donald.cormack@utoronto.ca




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
Top
Wayne G. O'Shea

SR3500 Fus-409/Pulley BB-128

Post by Wayne G. O'Shea » Fri Feb 17, 2012 9:38 pm

Don, sounds like MAM has a larger set (of Fus-409's) for the asking, why not
check that out and go with the larger pulleys you have if you haven't
drilled the holes through the fin mount yet!? Probably what I should do also
(or make my own) as I haven't drilled the holes through the fin bracket, but
the Fus-409 pulley brackets are already drilled and cleco'd in place at
3/32".

Have you put a pulley, bolt and bracket pair together, to see if in fact you
don't already have the larger Fus-409's?

Regards,
Wayne G. O'Shea
www.irishfield.on.ca


----- Original Message -----
From: "Don Cormack" <donald.cormack@utoronto.ca>
To: <murphy-rebel@dcsol.com>
Cc: <murphy-rebel@dcsol.com>
Sent: Tuesday, January 15, 2002 6:10 PM
Subject: Re: RE: SR3500 Fus-409/Pulley BB-128

I have SR 087. My pulleys are of the larger diameter and require either a
larger bracket or a shim. I haven't yet actually mounted my pulleys. So I
may
look for smaller ones, to avoid extra holes in the fin mount.

Don

On Tue, 15 Jan 2002 11:07:32 -0900 Mike Kimball <mkimball@gci.net> wrote:
This surprises me because I have serial number 44 which I bought almost
5
years ago from MAM which is a pretty early kit and I had no trouble at
all.
The brackets, pulleys, hole alignment all worked fine.

Mike Kimball
SR#044

-----Original Message-----
From: murphy-rebel@dcsol.com [mailto:murphy-rebel@dcsol.com]On Behalf Of
Wayne G. O'Shea
Sent: Monday, January 14, 2002 6:52 PM
To: murphy-rebel@dcsol.com
Subject: Re: SR3500 Fus-409/Pulley BB-128


Al, thanks! That is what I figured and maybe I should dig a little
harder
through all the boxes and see if there is another set of FUS-409's here.
I
don't think there are though, so I will check through my pulley stock in
my
NOS stuff and see if I have some with a smaller O.D. so I can use the
cotter
hole and a similar 1.9" cable groove diameter so no extra stress on the
cables. I noticed that these BB-128 pulleys have a really deep side
wall, so
there must be a pulley with a smaller O.D and the same cable groove
diameter. Just don't want to drill those 1/2" holes through the fin
attach
at the current location and then change pulleys and have to make them
into
slots!

Wayne G. O'Shea
www.irishfield.on.ca


----- Original Message -----
From: "Al & Deb Paxhia" <paxhia2@attbi.com>
To: <murphy-rebel@dcsol.com>
Sent: Monday, January 14, 2002 10:34 PM
Subject: Re: SR3500 Fus-409/Pulley BB-128

Hi Wayne,
Well as I best remember, the folks at MAM said they discontinued the
smaller
pulley and I was short one. Then I received a larger FUS409 bracket
and
larger pulleys, the larger bracket and pulleys did not align with the
hole
in the fin. I used the original smaller 409 and ordered a smaller
pulley
from Aircraft Spruce. All went together OK we will see how it works.
Al
SR#26
----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <murphy-rebel@dcsol.com>
Sent: Monday, January 14, 2002 6:15 PM
Subject: SR3500 Fus-409/Pulley BB-128

builders,
get
some
done
to
it.
the
fins
the
two
in
the
predrilled
enough
remember
diameters
I
can't
here??
a
**
itself
**
http://rebel:builder@www.dcsol.com:81/default.htm
** **


** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
** Archives located at
http://rebel:builder@www.dcsol.com:81/default.htm
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**


** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**

** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**
----------------------
Donald E. Cormack
Vice Dean,
School of Graduate Studies, and
Professor of Chemical Engineering
65 St. George Street
University of Toronto
Toronto, Canada M5S 2Z9
Tel: (416)978-2384 FAX: (416)978-1649
donald.cormack@utoronto.ca


** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
Top
Wayne G. O'Shea

SR3500 Fus-409/Pulley BB-128

Post by Wayne G. O'Shea » Fri Feb 17, 2012 9:38 pm

Didn't go the first/second time due to the server problems!

----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: "Murphy Rebel Builders List" <murphy-rebel@dcsol.com>
Sent: Tuesday, January 15, 2002 11:01 PM
Subject: RE: SR3500 Fus-409/Pulley BB-128


Don, sounds like MAM has a larger set (of Fus-409's) for the asking, why
not
check that out and go with the larger pulleys you have if you haven't
drilled the holes through the fin mount yet!? Probably what I should do
also
(or make my own) as I haven't drilled the holes through the fin bracket,
but
the Fus-409 pulley brackets are already drilled and cleco'd in place at
3/32".

Have you put a pulley, bolt and bracket pair together, to see if in fact
you
don't already have the larger Fus-409's?

Regards,
Wayne G. O'Shea
www.irishfield.on.ca


----- Original Message -----
From: "Don Cormack" <donald.cormack@utoronto.ca>
To: <murphy-rebel@dcsol.com>
Cc: <murphy-rebel@dcsol.com>
Sent: Tuesday, January 15, 2002 6:10 PM
Subject: Re: RE: SR3500 Fus-409/Pulley BB-128

I have SR 087. My pulleys are of the larger diameter and require
either
a
larger bracket or a shim. I haven't yet actually mounted my pulleys.
So
I
may
look for smaller ones, to avoid extra holes in the fin mount.

Don

On Tue, 15 Jan 2002 11:07:32 -0900 Mike Kimball <mkimball@gci.net>
wrote:
almost
5
at
all.
Behalf
Of
harder
here.
I
stock
in
my
the
cotter
the
wall, so
attach
them
into
the
bracket
and
the
hole
pulley
works.
SR
to
get
be
done
into
it.
through
the
that
the
big
in
from
the
enough
remember
diameters
but
I
into
with
a
with
itself
itself
**
http://rebel:builder@www.dcsol.com:81/default.htm
**
**
----------------------
Donald E. Cormack
Vice Dean,
School of Graduate Studies, and
Professor of Chemical Engineering
65 St. George Street
University of Toronto
Toronto, Canada M5S 2Z9
Tel: (416)978-2384 FAX: (416)978-1649
donald.cormack@utoronto.ca


** To unsubscribe, send e-mail to list-server@dcsol.com with
**
** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself
**
** Archives located at
http://rebel:builder@www.dcsol.com:81/default.htm
**
** To contact the list admin, e-mail mike.davis@dcsol.com
**


-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
Top
Locked

Return to “Rebel Builders List”