Do you want this big green box to go away? Well here's how...

Click here for full update

Wildcat! photo archives restored.

Click here for full update

Donors can now disable ads.

Click here for instructions

Add yourself to the user map.

Click here for instructions

[rebel-builders] Windshield instalation tip

Converted from Wildcat! database. (read only)
Locked
Ron Shannon

[rebel-builders] Windshield instalation tip

Post by Ron Shannon » Sun Feb 19, 2012 8:50 pm

A 3/8" belt sander also works well for forming the windshield. (It
happens to be my favorite tool. There's nothing like it for a whole
host of jobs, including sanding down to a fine line inside cutouts for
the panel, windows and doublers, finishing edges on fiberglass parts,
etc., etc.)

I think the rubber channel under the windshield is pretty important. I
would doubt that caulk can survive the movement the windshield
undergoes with thermal expansion. The rubber channel does add a slight
bump under the layup, but with a little care when fitting it prior to
drilling rivet holes, it will fit snugly.

I used 3M automotive bedding and glazing compound under the forward,
horizontal surface of the retainer, and butyl rubber between the
windshield and the rear, angled "vertical" portion of the retainer.
The glazing compound spreads easily so the retainer still sits tight
on top of the metal.

Ron


On Fri, Apr 29, 2011 at 4:47 PM, Charlie Eubanks
<charlie@troyairpark.com> wrote:
[quote]Hello All

Trimmed my Rebel windshield today, turned out pretty good, I would like to
pass on a tip for those of you who have yet to trim yours. If you have a
small 90

bransom

[rebel-builders] Windshield instalation tip

Post by bransom » Sun Feb 19, 2012 8:50 pm

Ron
I can't quite picture a 3/8" belt sander. What part of it is 3/8"?
-Ben

On 4/30/2011 8:41 AM, rshannon@cruzcom.com wrote to rebel-builders:
A 3/8" belt sander also works well for forming the windshield. (It
happens to be my favorite tool. There's nothing like it for a whole
host of jobs, including sanding down to a fine line inside cutouts for
the panel, windows and doublers, finishing edges on fiberglass parts,
etc., etc.)

I think the rubber channel under the windshield is pretty important. I
would doubt that caulk can survive the movement the windshield
undergoes with thermal expansion. The rubber channel does add a slight
bump under the layup, but with a little care when fitting it prior to
drilling rivet holes, it will fit snugly.

I used 3M automotive bedding and glazing compound under the forward,
horizontal surface of the retainer, and butyl rubber between the
windshield and the rear, angled "vertical" portion of the retainer.
The glazing compound spreads easily so the retainer still sits tight
on top of the metal.

Ron


On Fri, Apr 29, 2011 at 4:47 PM, Charlie Eubanks
<charlie@troyairpark.com> wrote:
Hello All

Trimmed my Rebel windshield today, turned out pretty good, I would
like to
pass on a tip for those of you who have yet to trim yours. If you have a
small 90

Ron Shannon

[rebel-builders] Windshield instalation tip

Post by Ron Shannon » Sun Feb 19, 2012 8:50 pm

The belt is 3/8" wide X 13" long. See
http://www.aircraft-tool.com/shop/detai ... D=ATS4501A

Best,
Ron


On Sun, May 1, 2011 at 9:14 AM, <bransom@dcsol.com> wrote:
[quote]Ron
I can't quite picture a 3/8" belt sander.

Ron Shannon

[rebel-builders] Windshield instalation tip

Post by Ron Shannon » Sun Feb 19, 2012 8:50 pm

FWIW, Brown Tool has better pricing on the belts. (See
http://tinyurl.com/6euxccg) I rarely use anything other than the 80
grit -- get a bunch.

The nose of this thing can be used at all kinds of angles, and will
get into some pretty small places. You'll still want to finish sand
edges with a fine grit by hand, but It's one of those tools that
you'll wonder how you ever managed to do without. Huge time saver.

Ron


On Sun, May 1, 2011 at 9:34 AM, Ron Shannon <rshannon@cruzcom.com> wrote:
The belt is 3/8" wide X 13" long. See
http://www.aircraft-tool.com/shop/detai ... D=ATS4501A

Best,
Ron

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Ken

[rebel-builders] Windshield instalation tip

Post by Ken » Sun Feb 19, 2012 8:50 pm

The cheap electric variable speed black and decker tool uses 1/2" x 18"
belts and one can cut six belts out of a 3" x 18" belt if one is on a
budget. Don't know about windshields but it is handy for some jobs.
Ken

On 5/1/2011 12:34 PM, Ron Shannon wrote:
The belt is 3/8" wide X 13" long. See
http://www.aircraft-tool.com/shop/detai ... D=ATS4501A

Best,
Ron


On Sun, May 1, 2011 at 9:14 AM,<bransom@dcsol.com> wrote:
Ron
I can't quite picture a 3/8" belt sander. What part of it is 3/8"?
-Ben

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------


drewjan

[rebel-builders] Windshield instalation tip

Post by drewjan » Sun Feb 19, 2012 8:50 pm

I found that an ordinary wood plane works very well for trimming plastic.
Sent on the TELUS Mobility network with BlackBerry

-----Original Message-----
From: Ron Shannon <rshannon@cruzcom.com>
Sender: mike.davis@dcsol.com
Date: Sat, 30 Apr 2011 09:41:06
To: <rebel-builders@dcsol.com>
Reply-to: rebel-builders@dcsol.com
Subject: Re: [rebel-builders] Windshield instalation tip

A 3/8" belt sander also works well for forming the windshield. (It
happens to be my favorite tool. There's nothing like it for a whole
host of jobs, including sanding down to a fine line inside cutouts for
the panel, windows and doublers, finishing edges on fiberglass parts,
etc., etc.)

I think the rubber channel under the windshield is pretty important. I
would doubt that caulk can survive the movement the windshield
undergoes with thermal expansion. The rubber channel does add a slight
bump under the layup, but with a little care when fitting it prior to
drilling rivet holes, it will fit snugly.

I used 3M automotive bedding and glazing compound under the forward,
horizontal surface of the retainer, and butyl rubber between the
windshield and the rear, angled "vertical" portion of the retainer.
The glazing compound spreads easily so the retainer still sits tight
on top of the metal.

Ron


On Fri, Apr 29, 2011 at 4:47 PM, Charlie Eubanks
<charlie@troyairpark.com> wrote:
[quote]Hello All

Trimmed my Rebel windshield today, turned out pretty good, I would like to
pass on a tip for those of you who have yet to trim yours. If you have a
small 90

bransom

[rebel-builders] Windshield instalation tip

Post by bransom » Sun Feb 19, 2012 8:50 pm

Thanks! I really didn't imagine there was a belt sander so thin. Knowing how
useful larger belt sanders are, I'll pick one up ...being cheap, I'll probably
check out that Black and Decker first.
- Ben

On 5/1/2011 8:48 AM, rshannon@cruzcom.com wrote to rebel-builders:
FWIW, Brown Tool has better pricing on the belts. (See
http://tinyurl.com/6euxccg) I rarely use anything other than the 80
grit -- get a bunch.

The nose of this thing can be used at all kinds of angles, and will
get into some pretty small places. You'll still want to finish sand
edges with a fine grit by hand, but It's one of those tools that
you'll wonder how you ever managed to do without. Huge time saver.

Ron


On Sun, May 1, 2011 at 9:34 AM, Ron Shannon <rshannon@cruzcom.com>
wrote:
The belt is 3/8" wide X 13" long. See
http://www.aircraft-tool.com/shop/detai ... D=ATS4501A

Best,
Ron


-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------


Locked