spinner

[Murray and Carol Cherkas]

Hello ALL

I need a 10" or 11" spinner with back plate for an 0-320, Sensenich prop.
Just asking incase anyone has changed props and has spare parts.

Thanks
Murray
cherkas@shaw.ca


*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
http://www.dcsol.com:81/public/code/html-subscribe.wcx
Archives located at http://rebel:builder@www.dcsol.com:81/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Ralph Baker]

Clay,
Van's also has a 13" fiberglas spinner if Wayne can't supply. The
fiberglas units are much easier to fit as you can see through them to
correct drill locations.
Ralph Baker
Elite 624E



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Clay Smith]

Thanks Ralph, I'll keep that in mind.

----- Original Message -----
From: "Ralph Baker" <rebaker@ftc-i.net>
To: <rebel-builders@dcsol.com>
Sent: Wednesday, September 08, 2004 9:55 PM
Subject: Spinner

Clay,
Van's also has a 13" fiberglas spinner if Wayne can't supply. The
fiberglas units are much easier to fit as you can see through them to
correct drill locations.
Ralph Baker
Elite 624E



-----------------------------------------------------
List archives located at:
https://www.dcsol.com/default.htm
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[indabush]

Anybody out there got some "spinner" info? I have the speed cowl (requires
13" diameter spinner), and will be getting a Prince prop (3.125" thick
with 3/8" crush plate).

Does the MAM spinner work?
Other sources? As far as I know UHS does not have a suitable model.

Mike.
_____________________________
Mike Ash, Rebel 305R



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Ralph Baker]

Van's has a 13" spinner with plates for the Sensenich fixed pitch prop. I went that route after reading the MAM instructions several times and not wanting to do all the work involved. The fiberglass is impeccable and easy to see through it to drill. The plates are completed.
Rallph Baker



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[indabush]

Thanks for he advice Rallph and Al. Vans says their FP-13 SEN spinner has
a design distance between the two bulkheads of 3.75 inches. My Prince
prop, with a crush plate, is 3.5 inches. and therefore a 1/4" spacer would
be required, and I will need new prop bolts. Having never done a spinner
before, I guess this is OK. I have been trying to get the design specs
from MAM for their spinner without any luck.. You know how that goes.

Mike
_____________________________
Michael Ash, 305R

You wrote:

Date: Sat, 29 Jul 2006 17:14:47 -0400
From: rebaker@sc.rr.com
To: rebel-builders
Subject: spinner

Van's has a 13" spinner with plates for the Sensenich fixed pitch prop. I
went that route after reading the MAM instructions several times and not
wanting to do all the work involved. The fiberglass is impeccable and
easy to see through it to drill. The plates are completed.
Rallph Baker

Date: Sun, 30 Jul 2006 17:32:10 -0400
From: ahepburn@xplornet.com
To: rebel-builders
Subject: RE: [rebel-builders] Spinner

Try the Vans 13" spinner. Works beautifully with the speed cowl.

Al




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------