Rebel stab leading edge skin

[apoulsen]

Hi,

This my first post although I've been reading along for some time.

I am building a Rebel in northern New Jersey and would like to contact
anyone in my area building a Rebel. My e-mail is apoulsen@comcast.net

My question for today concerns the leading edge skin on the stab. I
appears that both ends have to be trimmed yet there is no mention of
this in the manual. Since I'm trying to duplicate someone else's design
I don't want to just wing it (no pun intended) I'd appreciate knowing
what others have done here.

Thanks in advance.

Allen Poulsen
786R



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Ken]

Hi Allen
All I really remember is trimming the outboard end to match the outboard
rib. However my inboard end does end at the root rib. Later after
mounting the stabilizer, you make a fairing to close the couple of inch
space to the fuselage. It is not particularly unusual that all the
details are not spelled out in the manual. A lot of reading ahead is
necessary sometimes.
Ken

apoulsen wrote:

Hi,

This my first post although I've been reading along for some time.

I am building a Rebel in northern New Jersey and would like to contact
anyone in my area building a Rebel. My e-mail is apoulsen@comcast.net

My question for today concerns the leading edge skin on the stab. I
appears that both ends have to be trimmed yet there is no mention of
this in the manual. Since I'm trying to duplicate someone else's design
I don't want to just wing it (no pun intended) I'd appreciate knowing
what others have done here.

Thanks in advance.

Allen Poulsen
786R

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[apoulsen]

Hi Ken,

Thanks, I was expecting a little more guidance than the manual seems to
provide. As a newbie I really didn't know what to expect.

Allen
----- Original Message -----
From: "Ken" <klehman@albedo.net>
To: <rebel-builders@dcsol.com>
Sent: Thursday, September 22, 2005 9:45 PM
Subject: Re: Rebel stab leading edge skin

Hi Allen
All I really remember is trimming the outboard end to match the outboard
rib. However my inboard end does end at the root rib. Later after
mounting the stabilizer, you make a fairing to close the couple of inch
space to the fuselage. It is not particularly unusual that all the
details are not spelled out in the manual. A lot of reading ahead is
necessary sometimes.
Ken

apoulsen wrote:

Hi,

This my first post although I've been reading along for some time.

I am building a Rebel in northern New Jersey and would like to contact
anyone in my area building a Rebel. My e-mail is apoulsen@comcast.net

My question for today concerns the leading edge skin on the stab. I
appears that both ends have to be trimmed yet there is no mention of
this in the manual. Since I'm trying to duplicate someone else's design
I don't want to just wing it (no pun intended) I'd appreciate knowing
what others have done here.

Thanks in advance.

Allen Poulsen
786R

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[pequeajim]

Hi Allen:

I'm pretty close to buying a almost complete Rebel from a guy in Allentown,
PA. I am from New Holland, PA so if you like, after I get it, you are
welcome to stop by and look at, take pictures of anything that you like.

I would say that I am < 1.5 hour drive from Trenton.

Jim!


-> Hi,
->
-> This my first post although I've been reading along for some time.
->
-> I am building a Rebel in northern New Jersey and would like to contact
-> anyone in my area building a Rebel. My e-mail is apoulsen@comcast.net
->
-> My question for today concerns the leading edge skin on the stab. I
-> appears that both ends have to be trimmed yet there is no mention of
-> this in the manual. Since I'm trying to duplicate someone else's design
-> I don't want to just wing it (no pun intended) I'd appreciate knowing
-> what others have done here.
->
-> Thanks in advance.
->
-> Allen Poulsen
-> 786R





-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[apoulsen]

Jim,

Thanks. Please contact me off list and we can work something out.

Allen
----- Original Message -----
From: <pequeajim@dcsol.com>
To: <rebel-builders@dcsol.com>
Sent: Thursday, September 22, 2005 10:42 PM
Subject: RE: Rebel stab leading edge skin

Hi Allen:

I'm pretty close to buying a almost complete Rebel from a guy in
Allentown,
PA. I am from New Holland, PA so if you like, after I get it, you are
welcome to stop by and look at, take pictures of anything that you like.

I would say that I am < 1.5 hour drive from Trenton.

Jim!


-> Hi,
->
-> This my first post although I've been reading along for some time.
->
-> I am building a Rebel in northern New Jersey and would like to contact
-> anyone in my area building a Rebel. My e-mail is apoulsen@comcast.net
->
-> My question for today concerns the leading edge skin on the stab. I
-> appears that both ends have to be trimmed yet there is no mention of
-> this in the manual. Since I'm trying to duplicate someone else's design
-> I don't want to just wing it (no pun intended) I'd appreciate knowing
-> what others have done here.
->
-> Thanks in advance.
->
-> Allen Poulsen
-> 786R





-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------