engine mount 0-360

[Jerry Purdom]

Hi guy's I'm looking for info on 0-360 motor mount. I have talked to Murphy people,eg.Brian, Robin, about the flex in mount about 1/2",two AME I know they beleive that there should be no flex in the mount eg. bottom legs,and rubber mount. Is there any body out there that has some info. I bought FWF kit for Elite for my Rebel. THANKS jerry



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Al Paxhia]

I don't know how your detecting the flex in your motor mount. If your seeing
movement at the spinner or you can notice vibration when running the engine.
I would be suspect of the prop being out of balance. Unless you have a
friend with a dynamic balance setup go see your local prop shop. If the prop
was not dynamic balanced, you will be happy with the result.
Al
Moose, N526AP
----- Original Message -----
From: "Jerry Purdom" <jerrygoneflying@shaw.ca>
To: <murphy-rebel@dcsol.com>
Cc: "jerry purdom" <jerrygoneflying@shaw.ca>
Sent: Wednesday, November 26, 2003 6:08 PM
Subject: engine mount 0-360

Hi guy's I'm looking for info on 0-360 motor mount. I have talked to

Murphy people,eg.Brian, Robin, about the flex in mount about 1/2",two AME I
know they beleive that there should be no flex in the mount eg. bottom
legs,and rubber mount. Is there any body out there that has some info. I
bought FWF kit for Elite for my Rebel. THANKS jerry
*-------------------------------------------------------------------------*

To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*




*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Jerry Purdom]

Hi Al: I can see the flex when one person pushes up and down on spinner and
then you can see bottom legs of mount flex and rubber mounts move. I have
torque motor mount bolts down, Wayne says his mount flexes and that it
should move,the prop seems to be fine,its a Warp drive 4-blade climb (square
tip) prop.THANKS jerry
----- Original Message -----
From: Al Paxhia <paxhia2@comcast.net>
To: <murphy-rebel@dcsol.com>
Sent: Wednesday, November 26, 2003 7:57 PM
Subject: Re: engine mount 0-360

I don't know how your detecting the flex in your motor mount. If your

seeing

movement at the spinner or you can notice vibration when running the

engine.

I would be suspect of the prop being out of balance. Unless you have a
friend with a dynamic balance setup go see your local prop shop. If the

prop

was not dynamic balanced, you will be happy with the result.
Al
Moose, N526AP
----- Original Message -----
From: "Jerry Purdom" <jerrygoneflying@shaw.ca>
To: <murphy-rebel@dcsol.com>
Cc: "jerry purdom" <jerrygoneflying@shaw.ca>
Sent: Wednesday, November 26, 2003 6:08 PM
Subject: engine mount 0-360

Hi guy's I'm looking for info on 0-360 motor mount. I have talked to

Murphy people,eg.Brian, Robin, about the flex in mount about 1/2",two AME

I

know they beleive that there should be no flex in the mount eg. bottom
legs,and rubber mount. Is there any body out there that has some info. I
bought FWF kit for Elite for my Rebel. THANKS jerry

*-------------------------------------------------------------------------*

To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*
*-------------------------------------------------------------------------*

To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------