[rebel-builders] Wing attach hole size - Moose

[Ted Waltman]

Hello David,

I'll send you a copy of the 3500 mods "chapter 3 Fuselage Front Spar Attach
Fitting" document to your individual email address. FUS-712 is shown as
2"x2"x.120-128Wall 6061-T6.

Ted Waltman

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of davids
Sent: Wednesday, July 20, 2011 2:44 AM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Wing attach hole size - Moose

Hello
I am normally a lurker on this site, but have come upon a
problem and seek advice. In fitting the wing to the front
attach point, the manual calls for a 1/2" reamed hole, the
modification manual calls for a 1/2" hole and a bushing part
number W-712. Does anyone have final size dimensions and
materials spec for this bushing as there weren't any
bushings in the materials that I received. Holes were
previously drilled to 3/4" which makes sense for a bushing
and a 1/2" bolt, but of course there is ever present lack of
direction in the manuals.
Thanks & regards,
David Sproule




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rhuzzey]

Hi Ted

Could you send me that document as well.
I am never quite sure what I will run into building my Yukon as the manual was not completed.
Would be good to have infomation.

Thanks
Reid

Sent from my iPad

On 2011-07-20, at 12:45 PM, "Ted Waltman" <ted@vafm.org> wrote:

Hello David,

I'll send you a copy of the 3500 mods "chapter 3 Fuselage Front Spar Attach
Fitting" document to your individual email address. FUS-712 is shown as
2"x2"x.120-128Wall 6061-T6.

Ted Waltman

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of davids
Sent: Wednesday, July 20, 2011 2:44 AM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Wing attach hole size - Moose

Hello
I am normally a lurker on this site, but have come upon a
problem and seek advice. In fitting the wing to the front
attach point, the manual calls for a 1/2" reamed hole, the
modification manual calls for a 1/2" hole and a bushing part
number W-712. Does anyone have final size dimensions and
materials spec for this bushing as there weren't any
bushings in the materials that I received. Holes were
previously drilled to 3/4" which makes sense for a bushing
and a 1/2" bolt, but of course there is ever present lack of
direction in the manuals.
Thanks & regards,
David Sproule




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[David Sproule]

Thank you Ted, this is very much appreciated.
Best regards,
David Sproule

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Ted
Waltman
Sent: July-20-11 11:45 AM
To: rebel-builders@dcsol.com
Subject: RE: [rebel-builders] Wing attach hole size - Moose

Hello David,

I'll send you a copy of the 3500 mods "chapter 3 Fuselage Front Spar Attach
Fitting" document to your individual email address. FUS-712 is shown as
2"x2"x.120-128Wall 6061-T6.

Ted Waltman

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of davids
Sent: Wednesday, July 20, 2011 2:44 AM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Wing attach hole size - Moose

Hello
I am normally a lurker on this site, but have come upon a
problem and seek advice. In fitting the wing to the front
attach point, the manual calls for a 1/2" reamed hole, the
modification manual calls for a 1/2" hole and a bushing part
number W-712. Does anyone have final size dimensions and
materials spec for this bushing as there weren't any
bushings in the materials that I received. Holes were
previously drilled to 3/4" which makes sense for a bushing
and a 1/2" bolt, but of course there is ever present lack of
direction in the manuals.
Thanks & regards,
David Sproule




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------