[rebel-builders] Elite - SR/Moose Drooped Wing tips

[michael betti]

Bob,
Hurry up and finish that project, I am interested in hearing your
about your flights. I think that is the case wih my tips too, but I am
out of town and can't look at it for a couple days. I didn't mess with
them, I refuse to do any unnecessary glass work.
Mike

----Original Message----
From: robert@montanasky.us
Date: 04/16/2007 8:27
To: <rebel-builders@dcsol.com>
Subj: [rebel-builders] Elite - SR/Moose Drooped Wing tips

Mike,

Nice to see the fly-over picture of your Elite on your website ...
very
nice.

Yesterday I was fitting the extended drooped tips, and discovered the
chord
of the drooped tip is about an inch or so longer then the cord of my
Elite
wing w/ aileron. My thoughts are to remove trailing edge material
from the
tip between where the trailing edge of the aileron is and the existing
outboard trailing tip. And then glass what's left back together. Did
you
run into this same issue ?? Is the chord on the Elite smaller then on
the
SR and Moose? ... thought they were the same.

Cheers, Bob 612e




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------





-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Mike Betti]

Bob,
My tips too are about an 1" beyond as you mention.
Mike

----- Original Message -----
From: "Robert Andrews" <robert@montanasky.us>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 16, 2007 8:27 AM
Subject: [rebel-builders] Elite - SR/Moose Drooped Wing tips

Mike,

Nice to see the fly-over picture of your Elite on your website ... very
nice.

Yesterday I was fitting the extended drooped tips, and discovered the
chord
of the drooped tip is about an inch or so longer then the cord of my Elite
wing w/ aileron. My thoughts are to remove trailing edge material from
the
tip between where the trailing edge of the aileron is and the existing
outboard trailing tip. And then glass what's left back together. Did you
run into this same issue ?? Is the chord on the Elite smaller then on the
SR and Moose? ... thought they were the same.

Cheers, Bob 612e




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Robert Andrews]

Thanks Mike ... far be it from me to break the mold ... guess all flying
Drooped tipped Elites will look the same ... well, at least ours will ... :)

Bob

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
Mike Betti
Sent: Saturday, April 21, 2007 11:55 AM
To: rebel-builders@dcsol.com
Subject: Re: [rebel-builders] Elite - SR/Moose Drooped Wing tips


Bob,
My tips too are about an 1" beyond as you mention.
Mike

----- Original Message -----
From: "Robert Andrews" <robert@montanasky.us>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 16, 2007 8:27 AM
Subject: [rebel-builders] Elite - SR/Moose Drooped Wing tips

Mike,

Nice to see the fly-over picture of your Elite on your website ... very
nice.

Yesterday I was fitting the extended drooped tips, and discovered the
chord
of the drooped tip is about an inch or so longer then the cord of my Elite
wing w/ aileron. My thoughts are to remove trailing edge material from
the
tip between where the trailing edge of the aileron is and the existing
outboard trailing tip. And then glass what's left back together. Did you
run into this same issue ?? Is the chord on the Elite smaller then on the
SR and Moose? ... thought they were the same.

Cheers, Bob 612e




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------