Mike's flaperon actuator cover

[Angus McKenzie]

Hi Mike
Just got home from the shop and here are the dimensions.I cut the full
piece in half then trimmed the halves by nesting them to allow a 1"
mounting flange.The full width edge to edge is 4-3/4"s length is 9" but
length has yet to be trimmed for exact fit .I am going to drill out a
couple of wing rivets that the flange will cover and install C/Srivs so
it sits flat,anti-chafe tape on the underside then secure it with 5
#8PKs. Hope this helps.Also finished fitting and mounting one wing tip
and got the other partly finished.I wanted to get them on this week
before I put the floats on.
Regards, Angus



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Angus McKenzie]

Two and three quarters......Look forward to going flying with
you..........Angus
----- Original Message -----
From: "Jones, Michael" <MJones@hatch.ca>
To: <murphy-rebel@dcsol.com>
Sent: Wednesday, February 11, 2004 4:11 AM
Subject: RE: Mike's flaperon actuator cover

hi angus

these dims help alot, whats the insdie dim of the flange ??


-----Original Message-----
From: Angus McKenzie [mailto:angus@lweb.net]
Sent: Tuesday, February 10, 2004 9:39 PM
To: murphy-rebel@dcsol.com
Subject: Mike's flaperon actuator cover


Hi Mike
Just got home from the shop and here are the dimensions.I cut the full
piece in half then trimmed the halves by nesting them to allow a 1"
mounting flange.The full width edge to edge is 4-3/4"s length is 9" but
length has yet to be trimmed for exact fit .I am going to drill out a
couple of wing rivets that the flange will cover and install C/Srivs so
it sits flat,anti-chafe tape on the underside then secure it with 5
#8PKs. Hope this helps.Also finished fitting and mounting one wing tip
and got the other partly finished.I wanted to get them on this week
before I put the floats on.
Regards, Angus

*-------------------------------------------------------------------------*

To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*

----------------------------------------------------------------------

NOTICE - This message is the property of HATCH. It may also be
confidential and/or privileged. If you are not the intended recipient
of this message you are hereby notified that you must not disseminate,
copy or take any action with respect to it.

If you have received this message in error please notify
HATCH immediately via mailto:MailAdmin@hatch.ca.

*-------------------------------------------------------------------------*

To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Jones, Michael]

hi angus

these dims help alot, whats the insdie dim of the flange ??


-----Original Message-----
From: Angus McKenzie [mailto:angus@lweb.net]
Sent: Tuesday, February 10, 2004 9:39 PM
To: murphy-rebel@dcsol.com
Subject: Mike's flaperon actuator cover


Hi Mike
Just got home from the shop and here are the dimensions.I cut the full
piece in half then trimmed the halves by nesting them to allow a 1"
mounting flange.The full width edge to edge is 4-3/4"s length is 9" but
length has yet to be trimmed for exact fit .I am going to drill out a
couple of wing rivets that the flange will cover and install C/Srivs so
it sits flat,anti-chafe tape on the underside then secure it with 5
#8PKs. Hope this helps.Also finished fitting and mounting one wing tip
and got the other partly finished.I wanted to get them on this week
before I put the floats on.
Regards, Angus



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*



----------------------------------------------------------------------

NOTICE - This message is the property of HATCH. It may also be
confidential and/or privileged. If you are not the intended recipient
of this message you are hereby notified that you must not disseminate,
copy or take any action with respect to it.

If you have received this message in error please notify
HATCH immediately via mailto:MailAdmin@hatch.ca.


*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------