[rebel-builders] TAIL CONE STRINGERS (BEEF-UP)
Posted: Sun Feb 19, 2012 5:12 pm
Hi Kyle
Check out the SRfiles 101-1589 and 101-1599 I put 8 lengths of 3/4
extrusion from tail to cabin the only thing I did was to dremel out and
slide them in and use longer rivets.It made the tail cone strong,inexpensive
and I did not mind the weight back there as well.
Bill Pollock
Moose 244
----- Original Message -----
From: "kyle martin" <alpsnowman@gmail.com>
To: <rebel-builders@dcsol.com>
Sent: Tuesday, January 27, 2009 6:09 PM
Subject: [rebel-builders] TAIL CONE STRINGERS (BEEF-UP)
No virus found in this incoming message.
Checked by AVG - http://www.avg.com
Version: 8.0.176 / Virus Database: 270.10.14/1918 - Release Date: 1/27/2009
7:26 AM
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
Check out the SRfiles 101-1589 and 101-1599 I put 8 lengths of 3/4
extrusion from tail to cabin the only thing I did was to dremel out and
slide them in and use longer rivets.It made the tail cone strong,inexpensive
and I did not mind the weight back there as well.
Bill Pollock
Moose 244
----- Original Message -----
From: "kyle martin" <alpsnowman@gmail.com>
To: <rebel-builders@dcsol.com>
Sent: Tuesday, January 27, 2009 6:09 PM
Subject: [rebel-builders] TAIL CONE STRINGERS (BEEF-UP)
--------------------------------------------------------------------------------MOOSE BUILDERS,
FOR THOSE OF YOU WHO BEEFED UP THE TAIL CONE OF YOUR SR3500 USING THE 2"
U-CHANNEL MATERIAL, THAT IS INCORPORATED INTO MANY OTHER AREAS OF THE
AIRFRAME, AND RAN IT BETWEEN BULKHEADS:
I AM TRYING TO FIND THE MOST COST/TIME EFFECTIVE WAY TO MAKE, OR BUY 100'+
OF THIS TO INCORPORATE INTO A TAIL CONE BEEF-UP, SIMILAR TO HOW STEVE AND
MANY OTHERS DID IT; USING CORNER WRAPS AND ADDITIONAL STRINGERS IN FLOOR
AND
ROOF - THAT GO BETWEEN BULKHEADS.
MAM WANTS WAY TOO MUCH PER FOOT FOR THEIR U CHANNEL MATERIAL, SO I NEED TO
FIGURE OUT ANOTHER WAY. ANY ADVICE IS APPRECIATED.
THANKS
KYLE
019SR
On Mon, Jan 26, 2009 at 4:59 PM, <bransom@dcsol.com> wrote:
I meant to say that MAM instructions are to drill the two additional
holes.
Mine (496R) doesn't have the holes predrilled either, which just seems a
little odd since the rest of the holes are already there. Guess I'll
just
go ahead and drill them for now.
-Ben
AreHi Ben
Mine don't have those holes. May be it because mine is a later S/N 802R
Charlie
----- Original Message -----
From: <bransom@dcsol.com>
To: <rebel-builders@dcsol.com>
Sent: Monday, January 26, 2009 10:41 AM
Subject: [rebel-builders] rear spar attach bracket
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
No virus found in this incoming message.
Checked by AVG - http://www.avg.com
Version: 8.0.176 / Virus Database: 270.10.14/1918 - Release Date: 1/27/2009
7:26 AM
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------