The Murphy Builders Site

From: brownell@candlelight.ca
To: rebel-builders@dcsol.com
Subject: [rebel-builders] bottom front corner wraps FUS 70
Date: Fri, 5 Dec 2008 09:03:39 -0500

Hi all
would anyone have a close up picture of the bottom side of where the
bottom front
corner wrap meets the cage and the fus 2's.Feel a little stupid here
but I just can't get
those slots cut properly.A picture or any advice on this one would be
greatly appreciated.

Thanks Jason B
817R



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Jason,
I made it out of card stock (thin cardboard) first, then used that for a
pattern. It is a tricky area and you have to just hold/clamp/cleco it in
place while you make marks for the slots.
I ended up making those wraps from .032 sheet which adds some difficulty
too.

From: brownell@candlelight.ca
To: rebel-builders@dcsol.com
Subject: [rebel-builders] bottom front corner wraps FUS 70
Date: Fri, 5 Dec 2008 09:03:39 -0500

Hi all
would anyone have a close up picture of the bottom side of where the
bottom front
corner wrap meets the cage and the fus 2's.Feel a little stupid here
but I just can't get
those slots cut properly.A picture or any advice on this one would be
greatly appreciated.

Thanks Jason B
817R



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

_________________________________________________________________
You live life online. So we put Windows on the web.
http://clk.atdmt.com/MRT/go/127032869/direct/01/



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Yes as Jesse says, and as it shown in the pictures I sent you
previously
Jason, you make ALL your corner wraps with poster board first. It's
~ the
same thickness so works nice... you hack out an oversized hole and
then
place on the fuselage. Then use masking tape to close in the hacked
out hole
to form the perfect slot. Transfer to aluminum when happy with fit.

Wayne

----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: "Builders list" <rebel-builders@dcsol.com>
Sent: Friday, December 05, 2008 11:36 AM
Subject: RE: [rebel-builders] bottom front corner wraps FUS 70

Jason,
I made it out of card stock (thin cardboard) first, then used that
for a
pattern. It is a tricky area and you have to just hold/clamp/cleco
it in
place while you make marks for the slots.
I ended up making those wraps from .032 sheet which adds some
difficulty
too.

From: brownell@candlelight.ca
To: rebel-builders@dcsol.com
Subject: [rebel-builders] bottom front corner wraps FUS 70
Date: Fri, 5 Dec 2008 09:03:39 -0500

Hi all
would anyone have a close up picture of the bottom side of where the
bottom front
corner wrap meets the cage and the fus 2's.Feel a little stupid here
but I just can't get
those slots cut properly.A picture or any advice on this one would
be
greatly appreciated.

Thanks Jason B
817R



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

_________________________________________________________________
You live life online. So we put Windows on the web.
http://clk.atdmt.com/MRT/go/127032869/direct/01/



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------