The Murphy Builders Site

Can't believe it...I think I'm going to jump. Shoot, the hangar is on
ground level so I can't do that. Wait, I could get up on the roof.

Geez, I put on the right wing-tip. Look beautiful. Got everything ready
to put the LEFT droop-tip on. Trim the tip on my work-table. Just
beautiful. Carry the tip over to the wing to slip over the stringer and
spar extensions.

What? Huh?

@$#@% @%$^&&*$%* #^#&#$&#

Guess what? When I picked up my fast build and tip kit--YEP, I have TWO
(yes 2) RIGHT tips and NO left tip. ARGH!!

Bet it would cost a fortune to ship a correct LEFT WING DROOP TIP. I
can't believe this!

Got any ideas? All I can think of are:

- Find something going to the states and piggy-back on the shipment.
- Spend HUGE bucks to ship just for one wing tip to Colorado
- Somehow make a mold and create a new tip (major hours and effort that
may not pay off as desired)
- ????

Boy oh boy, I could scream. Skip the beer; Time for the scotch.

HELP!

Ted



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Just take the other tip off and fly it up to
Chilliwack to pick up the
correct tip... might as well have some fun with it!

Seriously, when the flap skins for my Moose turned
out to be wrong, MAM
shipped me new ones at no cost... and I'm sure that
wasn't cheap. Assuming
that this is their fault, and you didn't go into the
factory and pick out
the tips yourself, then I would think that MAM will
cover it.

Mike

----- Original Message -----
From: "Ted Waltman" <tedwaltman@infopipe.com>
To: <rebel-builders@dcsol.com>
Sent: Saturday, February 23, 2008 12:57 PM
Subject: [rebel-builders] Moose: Droop tip install

Can't believe it...I think I'm going to jump.

Shoot, the hangar is on

ground level so I can't do that. Wait, I could

get up on the roof.

Geez, I put on the right wing-tip. Look

beautiful. Got everything ready

to put the LEFT droop-tip on. Trim the tip on my

work-table. Just

beautiful. Carry the tip over to the wing to slip

over the stringer and

spar extensions.

What? Huh?

@$#@% @%$^&&*$%* #^#&#$&#

Guess what? When I picked up my fast build and

tip kit--YEP, I have TWO

(yes 2) RIGHT tips and NO left tip. ARGH!!

Bet it would cost a fortune to ship a correct LEFT

WING DROOP TIP. I

can't believe this!

Got any ideas? All I can think of are:

- Find something going to the states and

piggy-back on the shipment.

- Spend HUGE bucks to ship just for one wing tip

to Colorado

- Somehow make a mold and create a new tip (major

hours and effort that

may not pay off as desired)
- ????

Boy oh boy, I could scream. Skip the beer; Time

for the scotch.

HELP!

Ted

List archives located at:

https://mail.dcsol.com/login

username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com

List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com