Page 1 of 1
[rebel-builders] Engine Mount rivets
Posted: Sun Feb 19, 2012 4:11 pm
by Wayne G. O'Shea
When did SG-4 become an engine mount bracket?
I'd suggest someone with dyslexia typed the part number and it should be
RV1613 !
Yes RR-5604's are stainless.
Wayne
----- Original Message -----
From: <
n743ta@comcast.net>
To: <
rebel-builders@dcsol.com>
Sent: Thursday, December 06, 2007 11:18 AM
Subject: [rebel-builders] Engine Mount rivets
i'm about to rivet the engine mount brackets - SG-4.
Instructions call for an RV-1631 rivet - which I do not have.
As an alternate can I substitute either an RV-1613, RV-5604, or RV-1619.
Also - what is an RV 5604? is it stainless steel?
Tom Anderson R259
-----------------------------------------------------------------
List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe:
rebel-builders-unsubscribe@dcsol.com
List administrator:
mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe:
rebel-builders-unsubscribe@dcsol.com
List administrator:
mike.davis@dcsol.com
-----------------------------------------------------------------
[rebel-builders] Engine Mount rivets
Posted: Sun Feb 19, 2012 4:11 pm
by n743ta
thank you wayne.
I purchased MR from guy that started kit in 1993 and never finished. Instructions from that era. It makes sense that RV1631 is typo and it should be 1613.
but - i don't have but 20 or so of the 1613. So would you suggest it's ok to use rr-5604's?
tom anderson r259
-------------- Original message ----------------------
From: "Wayne G. O'Shea" <
oifa@irishfield.on.ca>
When did SG-4 become an engine mount bracket?
I'd suggest someone with dyslexia typed the part number and it should be
RV1613 !
Yes RR-5604's are stainless.
Wayne
----- Original Message -----
From: <
n743ta@comcast.net>
To: <
rebel-builders@dcsol.com>
Sent: Thursday, December 06, 2007 11:18 AM
Subject: [rebel-builders] Engine Mount rivets
i'm about to rivet the engine mount brackets - SG-4.
Instructions call for an RV-1631 rivet - which I do not have.
As an alternate can I substitute either an RV-1613, RV-5604, or RV-1619.
Also - what is an RV 5604? is it stainless steel?
Tom Anderson R259
-----------------------------------------------------------------
List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe:
rebel-builders-unsubscribe@dcsol.com
List administrator:
mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe:
rebel-builders-unsubscribe@dcsol.com
List administrator:
mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe:
rebel-builders-unsubscribe@dcsol.com
List administrator:
mike.davis@dcsol.com
-----------------------------------------------------------------
[rebel-builders] Engine Mount rivets
Posted: Sun Feb 19, 2012 4:11 pm
by Wayne G. O'Shea
I wouldn't. Don' t like the way they pull (they don't make nice shop heads)
and the mandrels usually fall out when pulled. Get some RV1613's from MAM.
Wayne
----- Original Message -----
From: <
n743ta@comcast.net>
To: <
rebel-builders@dcsol.com>
Sent: Thursday, December 06, 2007 4:41 PM
Subject: Re: [rebel-builders] Engine Mount rivets
thank you wayne.
I purchased MR from guy that started kit in 1993 and never finished.
Instructions from that era. It makes sense that RV1631 is typo and it
should be 1613.
but - i don't have but 20 or so of the 1613. So would you suggest it's ok
to use rr-5604's?
tom anderson r259
-------------- Original message ----------------------
From: "Wayne G. O'Shea" <
oifa@irishfield.on.ca>
When did SG-4 become an engine mount bracket?
I'd suggest someone with dyslexia typed the part number and it should be
RV1613 !
Yes RR-5604's are stainless.
Wayne
----- Original Message -----
From: <
n743ta@comcast.net>
To: <
rebel-builders@dcsol.com>
Sent: Thursday, December 06, 2007 11:18 AM
Subject: [rebel-builders] Engine Mount rivets
i'm about to rivet the engine mount brackets - SG-4.
Instructions call for an RV-1631 rivet - which I do not have.
As an alternate can I substitute either an RV-1613, RV-5604, or
RV-1619.
Also - what is an RV 5604? is it stainless steel?
Tom Anderson R259
-----------------------------------------------------------------
List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe:
rebel-builders-unsubscribe@dcsol.com
List administrator:
mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe:
rebel-builders-unsubscribe@dcsol.com
List administrator:
mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe:
rebel-builders-unsubscribe@dcsol.com
List administrator:
mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe:
rebel-builders-unsubscribe@dcsol.com
List administrator:
mike.davis@dcsol.com
-----------------------------------------------------------------
[rebel-builders] Engine Mount rivets
Posted: Sun Feb 19, 2012 4:11 pm
by Ken
And the stainless pop rivets don't expand radially. So despite being
stronger they are more likely to smoke or move from engine vibration. I
agree with Wayne. 3/16" diameter avex are available from many sources.
If all else fails I probably have enough spare 1613 (or they might be
the longer 1619) that I can put in the mail.
Ken
Wayne G. O'Shea wrote:
I wouldn't. Don' t like the way they pull (they don't make nice shop heads)
and the mandrels usually fall out when pulled. Get some RV1613's from MAM.
Wayne
-----------------------------------------------------------------
List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe:
rebel-builders-unsubscribe@dcsol.com
List administrator:
mike.davis@dcsol.com
-----------------------------------------------------------------
[rebel-builders] Engine Mount rivets
Posted: Sun Feb 19, 2012 4:11 pm
by n743ta
Thanks for the comments. I am going to take your advise and get some 1613's.
Tom Anderson R259
-------------- Original message ----------------------
From: Ken <
klehman@albedo.net>
And the stainless pop rivets don't expand radially. So despite being
stronger they are more likely to smoke or move from engine vibration. I
agree with Wayne. 3/16" diameter avex are available from many sources.
If all else fails I probably have enough spare 1613 (or they might be
the longer 1619) that I can put in the mail.
Ken
Wayne G. O'Shea wrote:
I wouldn't. Don' t like the way they pull (they don't make nice shop heads)
and the mandrels usually fall out when pulled. Get some RV1613's from MAM.
Wayne
-----------------------------------------------------------------
List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe:
rebel-builders-unsubscribe@dcsol.com
List administrator:
mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe:
rebel-builders-unsubscribe@dcsol.com
List administrator:
mike.davis@dcsol.com
-----------------------------------------------------------------