[rebel-builders] Rivnut vs Anchor Nut
Posted: Sun Feb 19, 2012 11:13 am
Actually, Ralph's suggestion of the clip on Tinnerman nut is better
still. Leaves a gap of 10 thou or so, but you've got to be awfully
picky to notice.
Al
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
Ted Waltman
Sent: October 3, 2006 8:15 AM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Rivnut vs Anchor Nut
You're right Alan, there are other options. Slightly faster and less
expensive to put in a rivnut would be my only response. There is a new
Cherry brand anchor nut that I saw on-line that is a single pull-rivet
installation. I might order some of those to try them.
Ted
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
Alan Hepburn
Sent: Monday, October 02, 2006 6:44 PM
To: rebel-builders@dcsol.com
Subject: RE: [rebel-builders] Rivnut dimple for access covers
Why not use an anchor nut (e.g. A6195-6Z-1D)?
Al
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
Ted Waltman
Sent: October 2, 2006 12:19 PM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Rivnut dimple for access covers
I just uploaded two pictures of access covers that I have where they
have been dimpled for rivnuts. I've looked all over the web and can't
find any tool that creates these large dimples for rivnuts. Has anyone
on the list seen such a tool to create these rivnut dimples or is this
some totally custom deal that someone made?
The pics are in area 123 S/M Miscellaneous.
Thanks in advance...
Ted
-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login username "rebel"
password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login username "rebel"
password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
still. Leaves a gap of 10 thou or so, but you've got to be awfully
picky to notice.
Al
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
Ted Waltman
Sent: October 3, 2006 8:15 AM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Rivnut vs Anchor Nut
You're right Alan, there are other options. Slightly faster and less
expensive to put in a rivnut would be my only response. There is a new
Cherry brand anchor nut that I saw on-line that is a single pull-rivet
installation. I might order some of those to try them.
Ted
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
Alan Hepburn
Sent: Monday, October 02, 2006 6:44 PM
To: rebel-builders@dcsol.com
Subject: RE: [rebel-builders] Rivnut dimple for access covers
Why not use an anchor nut (e.g. A6195-6Z-1D)?
Al
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
Ted Waltman
Sent: October 2, 2006 12:19 PM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Rivnut dimple for access covers
I just uploaded two pictures of access covers that I have where they
have been dimpled for rivnuts. I've looked all over the web and can't
find any tool that creates these large dimples for rivnuts. Has anyone
on the list seen such a tool to create these rivnut dimples or is this
some totally custom deal that someone made?
The pics are in area 123 S/M Miscellaneous.
Thanks in advance...
Ted
-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login username "rebel"
password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login username "rebel"
password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------