The Murphy Builders Site

Hi Guys: I am just completing running all the hydraulic lines for the

At 09:22 AM 9/7/2006 -0400, you wrote:

Hi Guys: I am just completing running all the hydraulic lines for the

electric and manual pump systems for Moose 226. Amphibious floats to be
added later. I have one pressure gauge which I assume (there's that famous
word again) should go in the gear down side of the system teed into that
line. Is this correct?? Thanks to all who respond and have "been there
done
that" Bob J Moose 226

If you tee the gauge off the line from the pump to the selector you'll be
able to read the pressure both gear up and down.
Drew



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

From: Robert and Olga Johnson <rjohnson18@cogeco.ca>
Reply-To: rebel-builders@dcsol.com
Date: Thu, 07 Sep 2006 10:41:14 -0400
To: rebel-builders@dcsol.com
Subject: Re: [rebel-builders] Floats hyd system

Thanks Drew, but this manual pump has a built in selector valve with neutral
position and must be in the neutral position when operating the electric
pump. Bob J
----- Original Message -----
From: "Drew Dalgleish" <drewjan@cabletv.on.ca>
To: <rebel-builders@dcsol.com>
Sent: Thursday, September 07, 2006 9:53 AM
Subject: Re: [rebel-builders] Floats hyd system

At 09:22 AM 9/7/2006 -0400, you wrote:

Hi Guys: I am just completing running all the hydraulic lines for the

electric and manual pump systems for Moose 226. Amphibious floats to be
added later. I have one pressure gauge which I assume (there's that famous
word again) should go in the gear down side of the system teed into that
line. Is this correct?? Thanks to all who respond and have "been there
done
that" Bob J Moose 226

If you tee the gauge off the line from the pump to the selector you'll be
able to read the pressure both gear up and down.
Drew



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Hi Guys: I am just completing running all the hydraulic lines for the
electric and manual pump systems for Moose 226. Amphibious floats to be
added later. I have one pressure gauge which I assume (there's that famous
word again) should go in the gear down side of the system teed into that
line. Is this correct?? Thanks to all who respond and have "been there
done that" Bob J Moose 226



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

From: "Robert and Olga Johnson" <rjohnson18@cogeco.ca>
Reply-To: <rebel-builders@dcsol.com>
To: <rebel-builders@dcsol.com>
Subject: Re: [rebel-builders] Floats hyd system
Date: Thu, 7 Sep 2006 10:41:14 -0400

Thanks Drew, but this manual pump has a built in selector valve with
neutral
position and must be in the neutral position when operating the electric
pump. Bob J
----- Original Message -----
From: "Drew Dalgleish" <drewjan@cabletv.on.ca>
To: <rebel-builders@dcsol.com>
Sent: Thursday, September 07, 2006 9:53 AM
Subject: Re: [rebel-builders] Floats hyd system

At 09:22 AM 9/7/2006 -0400, you wrote:

Hi Guys: I am just completing running all the hydraulic lines for the

electric and manual pump systems for Moose 226. Amphibious floats to be
added later. I have one pressure gauge which I assume (there's that

famous

word again) should go in the gear down side of the system teed into that
line. Is this correct?? Thanks to all who respond and have "been there
done
that" Bob J Moose 226

If you tee the gauge off the line from the pump to the selector you'll

be

able to read the pressure both gear up and down.
Drew



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Bob,
Who makes the manual pump? I don't know if it would work with the MAM
floats, but I would like to check it out. Having the selector build in
seems
like a big advantage plumbing wise.
Thanks.
Jesse

From: "Robert and Olga Johnson" <rjohnson18@cogeco.ca>
Reply-To: <rebel-builders@dcsol.com>
To: <rebel-builders@dcsol.com>
Subject: Re: [rebel-builders] Floats hyd system
Date: Thu, 7 Sep 2006 13:11:58 -0400

Jesse The pump is Parker Hydraulics #638203 model S7HP-3-N-00-B and was
supplied to me by the owner of the Moose. - Bob J
----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: <rebel-builders@dcsol.com>
Sent: Thursday, September 07, 2006 12:24 PM
Subject: Re: [rebel-builders] Floats hyd system

Bob,
Who makes the manual pump? I don't know if it would work with the MAM
floats, but I would like to check it out. Having the selector build in
seems
like a big advantage plumbing wise.
Thanks.
Jesse

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------