The Murphy Builders Site

For builders of Murphy Aircraft Manufacturing kits - Bringing builders together
https://www.murphybuilders.net/

[rebel-builders] Moose landing gear

https://www.murphybuilders.net/viewtopic.php?f=1&t=6071

Page 1 of 1

[rebel-builders] Moose landing gear

Posted: Sun Feb 19, 2012 10:31 am
by Dale Fultz
Bill, the new style is the 310B if the gear leg goes into the 309 and fits
flush then you use the flat bar type if the gear leg protrudes down out of
the 309 then you use the one with the little legs on it. Dale SR-033
----- Original Message -----
From: "pollock" <lbpollock@sympatico.ca>
To: <rebel-builders@dcsol.com>
Sent: Sunday, March 19, 2006 6:14 PM
Subject: [rebel-builders] Moose landing gear

I am working on the main landing gear box on the moose.I seem to have two
types of clamps Fus-310 seems to have 1/2 inch space and the other clamp
Fus -310B is a straight flat bar.I don't know which one to use any ideas???

Bill
Moose 244



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------





-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] Moose landing gear

Posted: Sun Feb 19, 2012 10:31 am
by pollock
I tried the gear leg and it does protrude so I will use Fus 310 which will
give me a bigger gap.I thinking the parts are labeled wrong.Fus 310B is the
flat bar and Fus 310 has more clearance???

Thanks for your reply

Bill
Moose 244
----- Original Message -----
From: "Dale Fultz" <dfultz17086@earthlink.net>
To: <rebel-builders@dcsol.com>
Sent: Sunday, March 19, 2006 6:52 PM
Subject: Re: [rebel-builders] Moose landing gear

Bill, the new style is the 310B if the gear leg goes into the 309 and
fits
flush then you use the flat bar type if the gear leg protrudes down out of
the 309 then you use the one with the little legs on it. Dale SR-033
----- Original Message -----
From: "pollock" <lbpollock@sympatico.ca>
To: <rebel-builders@dcsol.com>
Sent: Sunday, March 19, 2006 6:14 PM
Subject: [rebel-builders] Moose landing gear

I am working on the main landing gear box on the moose.I seem to have two
types of clamps Fus-310 seems to have 1/2 inch space and the other clamp
Fus -310B is a straight flat bar.I don't know which one to use any
ideas???

Bill
Moose 244



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------





-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] Moose landing gear

Posted: Sun Feb 19, 2012 10:31 am
by Wayne G. O'Shea
Why do you want clearance? You are trying to clamp the leg so it can't
twist/roll/etc. I highly suggest looking thru Scott's website for some
modification ideas to the main (single) bolt attach on the end of the leg.

Wayne


Wayne

----- Original Message -----
From: "pollock" <lbpollock@sympatico.ca>
To: <rebel-builders@dcsol.com>
Sent: Sunday, March 19, 2006 8:18 PM
Subject: Re: [rebel-builders] Moose landing gear

I tried the gear leg and it does protrude so I will use Fus 310 which
will
give me a bigger gap.I thinking the parts are labeled wrong.Fus 310B is
the
flat bar and Fus 310 has more clearance???

Thanks for your reply

Bill
Moose 244
----- Original Message -----
From: "Dale Fultz" <dfultz17086@earthlink.net>
To: <rebel-builders@dcsol.com>
Sent: Sunday, March 19, 2006 6:52 PM
Subject: Re: [rebel-builders] Moose landing gear

Bill, the new style is the 310B if the gear leg goes into the 309 and
fits
flush then you use the flat bar type if the gear leg protrudes down out
of
the 309 then you use the one with the little legs on it. Dale SR-033
----- Original Message -----
From: "pollock" <lbpollock@sympatico.ca>
To: <rebel-builders@dcsol.com>
Sent: Sunday, March 19, 2006 6:14 PM
Subject: [rebel-builders] Moose landing gear

I am working on the main landing gear box on the moose.I seem to have
two
types of clamps Fus-310 seems to have 1/2 inch space and the other clamp
Fus -310B is a straight flat bar.I don't know which one to use any
ideas???

Bill
Moose 244



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------





-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------







-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] Moose landing gear

Posted: Sun Feb 19, 2012 10:31 am
by pollock
I went up to Orillia aviation and there clamp mount was banana shaped .I
understand being tight but I don't think it should be distorting the clamp?

Bill
----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <rebel-builders@dcsol.com>
Sent: Sunday, March 19, 2006 8:25 PM
Subject: Re: [rebel-builders] Moose landing gear

Why do you want clearance? You are trying to clamp the leg so it can't
twist/roll/etc. I highly suggest looking thru Scott's website for some
modification ideas to the main (single) bolt attach on the end of the leg.

Wayne


Wayne

----- Original Message -----
From: "pollock" <lbpollock@sympatico.ca>
To: <rebel-builders@dcsol.com>
Sent: Sunday, March 19, 2006 8:18 PM
Subject: Re: [rebel-builders] Moose landing gear

I tried the gear leg and it does protrude so I will use Fus 310 which
will
give me a bigger gap.I thinking the parts are labeled wrong.Fus 310B is
the
flat bar and Fus 310 has more clearance???

Thanks for your reply

Bill
Moose 244
----- Original Message -----
From: "Dale Fultz" <dfultz17086@earthlink.net>
To: <rebel-builders@dcsol.com>
Sent: Sunday, March 19, 2006 6:52 PM
Subject: Re: [rebel-builders] Moose landing gear

Bill, the new style is the 310B if the gear leg goes into the 309 and
fits
flush then you use the flat bar type if the gear leg protrudes down out
of
the 309 then you use the one with the little legs on it. Dale SR-033
----- Original Message -----
From: "pollock" <lbpollock@sympatico.ca>
To: <rebel-builders@dcsol.com>
Sent: Sunday, March 19, 2006 6:14 PM
Subject: [rebel-builders] Moose landing gear

two


-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------







-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] Moose landing gear

Posted: Sun Feb 19, 2012 10:34 am
by Bill Smith
It sounds like they have a 309B mixed with a standard 310 not the
310B. Shouldn't be able to get much distortion (at least I wouldn't
think) with the 310B and 309B combo??

Cheers,
BS

----------------------------

I went up to Orillia aviation and there clamp mount was banana shaped .I
understand being tight but I don't think it should be distorting the clamp?

Bill
----- Original Message -----
From: "Wayne G. O'Shea"
To:
Sent: Sunday, March 19, 2006 8:25 PM
Subject: Re: [rebel-builders] Moose landing gear



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] Moose landing gear

Posted: Sun Feb 19, 2012 10:34 am
by Dale Fultz
Bill , You couldn't mix a 309B with a 310 and get distortion, because the B
series of the 309 has longer legs I will call them on it, and the 310 also
has legs on it which would create a gap in the leg area. If they mixed a 309
with a 310B there would be distortion. The common thing I believe is that
the 309's have a rounded corner on them where the leg fits into and the legs
are square cut and I seen one where the guy didn't round the corner of the
legs and couldn't get them to fit properly. Just my opinion on this. Dale
SR-033
----- Original Message -----
From: "Bill Smith" <smithbill2@gmail.com>
To: <rebel-builders@dcsol.com>
Sent: Tuesday, March 21, 2006 10:45 AM
Subject: Re: [rebel-builders] Moose landing gear

It sounds like they have a 309B mixed with a standard 310 not the
310B. Shouldn't be able to get much distortion (at least I wouldn't
think) with the 310B and 309B combo??

Cheers,
BS

----------------------------

I went up to Orillia aviation and there clamp mount was banana shaped .I
understand being tight but I don't think it should be distorting the
clamp?

Bill
----- Original Message -----
From: "Wayne G. O'Shea"
To:
Sent: Sunday, March 19, 2006 8:25 PM
Subject: Re: [rebel-builders] Moose landing gear



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------





-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] Moose landing gear

Posted: Sun Feb 19, 2012 10:34 am
by Bill Smith
Yeah, I just mixed up the part numbers but that is what I was thinking also.
BS

On 3/21/06, Dale Fultz <dfultz17086@earthlink.net> wrote:
Bill , You couldn't mix a 309B with a 310 and get distortion, because the B
series of the 309 has longer legs I will call them on it, and the 310 also
has legs on it which would create a gap in the leg area. If they mixed a 309
with a 310B there would be distortion. The common thing I believe is that
the 309's have a rounded corner on them where the leg fits into and the legs
are square cut and I seen one where the guy didn't round the corner of the
legs and couldn't get them to fit properly. Just my opinion on this. Dale
SR-033
----- Original Message -----
From: "Bill Smith" <smithbill2@gmail.com>
To: <rebel-builders@dcsol.com>
Sent: Tuesday, March 21, 2006 10:45 AM
Subject: Re: [rebel-builders] Moose landing gear

It sounds like they have a 309B mixed with a standard 310 not the
310B. Shouldn't be able to get much distortion (at least I wouldn't
think) with the 310B and 309B combo??

Cheers,
BS

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] Moose landing gear

Posted: Sun Feb 19, 2012 10:34 am
by pollock
I was talking to Murphy and part # Fus 705 has now been changed to Fus309B I
am finally breaking enigma code !
----- Original Message -----
From: "Bill Smith" <smithbill2@gmail.com>
To: <rebel-builders@dcsol.com>
Sent: Tuesday, March 21, 2006 4:15 PM
Subject: Re: [rebel-builders] Moose landing gear

Yeah, I just mixed up the part numbers but that is what I was thinking
also.
BS

On 3/21/06, Dale Fultz <dfultz17086@earthlink.net> wrote:
Bill , You couldn't mix a 309B with a 310 and get distortion, because the
B
series of the 309 has longer legs I will call them on it, and the 310
also
has legs on it which would create a gap in the leg area. If they mixed a
309
with a 310B there would be distortion. The common thing I believe is
that
the 309's have a rounded corner on them where the leg fits into and the
legs
are square cut and I seen one where the guy didn't round the corner of
the
legs and couldn't get them to fit properly. Just my opinion on this.
Dale
SR-033
----- Original Message -----
From: "Bill Smith" <smithbill2@gmail.com>
To: <rebel-builders@dcsol.com>
Sent: Tuesday, March 21, 2006 10:45 AM
Subject: Re: [rebel-builders] Moose landing gear

It sounds like they have a 309B mixed with a standard 310 not the
310B. Shouldn't be able to get much distortion (at least I wouldn't
think) with the 310B and 309B combo??

Cheers,
BS

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] Moose landing gear

Posted: Sun Feb 19, 2012 10:34 am
by Brian Godden
Nope...that is not correct. The 705 only accepts the original "c" 310 and
the 3500 leg, the 309B only accepts the new flat bar stock 310 and the 3500
leg.
You see, I have the enigma machine!!!

From: "pollock" <lbpollock@sympatico.ca>
Reply-To: <rebel-builders@dcsol.com>
To: <rebel-builders@dcsol.com>
Subject: Re: [rebel-builders] Moose landing gear
Date: Tue, 21 Mar 2006 20:39:45 -0500

I was talking to Murphy and part # Fus 705 has now been changed to Fus309B
I
am finally breaking enigma code !
----- Original Message -----
From: "Bill Smith" <smithbill2@gmail.com>
To: <rebel-builders@dcsol.com>
Sent: Tuesday, March 21, 2006 4:15 PM
Subject: Re: [rebel-builders] Moose landing gear

Yeah, I just mixed up the part numbers but that is what I was thinking
also.
BS

On 3/21/06, Dale Fultz <dfultz17086@earthlink.net> wrote:
Bill , You couldn't mix a 309B with a 310 and get distortion, because
the
B
series of the 309 has longer legs I will call them on it, and the 310
also
has legs on it which would create a gap in the leg area. If they mixed
a
309
with a 310B there would be distortion. The common thing I believe is
that
the 309's have a rounded corner on them where the leg fits into and the
legs
are square cut and I seen one where the guy didn't round the corner of
the
legs and couldn't get them to fit properly. Just my opinion on this.
Dale
SR-033
----- Original Message -----
From: "Bill Smith" <smithbill2@gmail.com>
To: <rebel-builders@dcsol.com>
Sent: Tuesday, March 21, 2006 10:45 AM
Subject: Re: [rebel-builders] Moose landing gear


-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------


_________________________________________________________________
Take advantage of powerful junk e-mail filters built on patented Microsoft

[rebel-builders] Moose landing gear

Posted: Sun Feb 19, 2012 10:34 am
by Warren & Marg Montgomery
HI Dale,

After 13:35 from Evertt to Dubai (6988 nm and M .86) I arrived safely
home with a shinny new 777 ER and Moose tail stinger.
Dropped 1500 at Sears for tools as well.
Nice workmanship on the parts!
Regards,
Warren

Dale Fultz wrote:
Bill, the new style is the 310B if the gear leg goes into the 309 and fits
flush then you use the flat bar type if the gear leg protrudes down out of
the 309 then you use the one with the little legs on it. Dale SR-03


-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
All times are UTC-09:00
Page 1 of 1
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/