The Murphy Builders Site

From: "Mike Betti" <mbetti@up.net>
Reply-To: <rebel-builders@dcsol.com>
To: <rebel-builders@dcsol.com>
Subject: Roof skin
Date: Sat, 11 Jun 2005 11:22:46 -0500

Hi all,
I'm getting ready to fit roof skin. Does the front edge actually go
behind the fus1. The top line of rivets are still out but it looks like
I would have to drill out the the row below them just so I can pry fus1
away far enough to get the skin behind it. Is this correct?
Thanks,
Mike Betti
771E



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Hi Mike
Buddy of mine realized that somewhere's in the manuel after the front
plates
are riveted in, it says not to rivet the top rows because of this. The
rows
of rivets in the top plates that go in the top cross member should be
clecoed until the roof is ready to go in. Don't have my manuel nearby but
the front edge of the roof goes behind the front root pickups or plates.
I
installed my skylites after I had the fuse completed with no problem. I
wasn't going to put them in but after a little stick time in the garage, I
realized as suggested by most on the site that at least the two front
windows shud be there. See ya in Osh!

Steve W. Rebel 637

From: "Mike Betti" <mbetti@up.net>
Reply-To: <rebel-builders@dcsol.com>
To: <rebel-builders@dcsol.com>
Subject: Roof skin
Date: Sat, 11 Jun 2005 11:22:46 -0500

Hi all,
I'm getting ready to fit roof skin. Does the front edge actually go
behind the fus1. The top line of rivets are still out but it looks like
I would have to drill out the the row below them just so I can pry fus1
away far enough to get the skin behind it. Is this correct?
Thanks,
Mike Betti
771E



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Hi all,
I'm getting ready to fit roof skin. Does the front edge actually go
behind the fus1. The top line of rivets are still out but it looks like
I would have to drill out the the row below them just so I can pry fus1
away far enough to get the skin behind it. Is this correct?
Thanks,
Mike Betti
771E



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Hi Mike: I am on a 2nd Rebel and both manuals state quite clearly "NOT TO
RIVET THE FRONT FUS 1 BRACKET AT ALL when assembling the cabin frame. I
also
wondered why, the first time around, until I read further ahead and saw
that
the roof skin does go under this bracket. That is a pretty stiff bracket -
lots of luck prying out. Bob J
----- Original Message -----
From: "Mike Betti" <mbetti@up.net>
To: <rebel-builders@dcsol.com>
Sent: Saturday, June 11, 2005 12:22 PM
Subject: Roof skin

Hi all,
I'm getting ready to fit roof skin. Does the front edge actually go
behind the fus1. The top line of rivets are still out but it looks like
I would have to drill out the the row below them just so I can pry fus1
away far enough to get the skin behind it. Is this correct?
Thanks,
Mike Betti
771E



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------