The Murphy Builders Site

Posted: **Sat Feb 18, 2012 10:24 am**

Where do you get the nylon washers called for in the elevator/rudder hinge?
I didn't get any with my kit. Are they an AN part, or hardware store?
Thanks.
Jesse

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:24 am**

Jesse, did I not throw a dozen in of my thrust washers?? MAM used to have
nothing there, then bought about 2000 from me and then switched to something
inferior in my mind. Give me your mailing address again and I send you some.

Wayne

----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 11, 2005 11:36 AM
Subject: nylon washers

Where do you get the nylon washers called for in the elevator/rudder

hinge?

I didn't get any with my kit. Are they an AN part, or hardware store?
Thanks.
Jesse

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:24 am**

I could use some also
Would be more than happy to pay for them
Thanks

Keith B. Oliver
ELITE N654ME (reserved)
Farmingdale, Maine

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
Wayne G. O'Shea
Sent: Monday, April 11, 2005 12:41 PM
To: rebel-builders@dcsol.com
Subject: Re: nylon washers

Jesse, did I not throw a dozen in of my thrust washers?? MAM used to have
nothing there, then bought about 2000 from me and then switched to something
inferior in my mind. Give me your mailing address again and I send you some.

Wayne

----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 11, 2005 11:36 AM
Subject: nylon washers

Where do you get the nylon washers called for in the elevator/rudder

hinge?

I didn't get any with my kit. Are they an AN part, or hardware store?
Thanks.
Jesse

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:24 am**

Jesse bought a whole airplane kit from me and why I said I'd send him some
N/C......

As previously posted......anyone that wants them just send me $5 >CASH< and
your address and I will send you a dozen. US folks US dollars and Canadian
folks CDN dollars, as this will cover the higher postage rate to the USA.

These are only for the Rebel though TTBOMKnowledge, so Keith I'm not sure if
you need them. The washers themselves are about 2" OD with a 3/8 ID hole
that fits the hinge bushing perfectly. They are about 0.032/0.040 thick and
made of nylon 6. You will never wear them out....OEM usage was the thrust
washer for TRW seatbelts, to keep the recoil spring from wearing thru the
Polypro case.

On the Rebel they are used between the hinge brackets and the
elevator/rudder spar tubes end plugs and the rivets holding the push pull
horns on. The rudder is absolutely critical as without the washer in place
the rivets will chew their way through the lower hinge bracket thanks to
gravity.

Cheers,
Wayne O'Shea
1516 Alvin Williams Rd
Penetanguishene, Ontario
L9M-2C1

----- Original Message -----
From: "Keith B. Oliver" <kb_oliver@verizon.net>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 11, 2005 4:22 PM
Subject: RE: nylon washers

I could use some also
Would be more than happy to pay for them
Thanks

Keith B. Oliver
ELITE N654ME (reserved)
Farmingdale, Maine

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
Wayne G. O'Shea
Sent: Monday, April 11, 2005 12:41 PM
To: rebel-builders@dcsol.com
Subject: Re: nylon washers

Jesse, did I not throw a dozen in of my thrust washers?? MAM used to have
nothing there, then bought about 2000 from me and then switched to

something

inferior in my mind. Give me your mailing address again and I send you

some.

Wayne

----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 11, 2005 11:36 AM
Subject: nylon washers

Where do you get the nylon washers called for in the elevator/rudder
hinge?
I didn't get any with my kit. Are they an AN part, or hardware store?
Thanks.
Jesse

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:24 am**

BTW, the exact dimensions for those that may have a need, OD = 1.85". ID
hole = 0.3985" and thickness is 0.042"

Wayne

----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 11, 2005 7:38 PM
Subject: Re: nylon washers

Jesse bought a whole airplane kit from me and why I said I'd send him some
N/C......

As previously posted......anyone that wants them just send me $5 >CASH<

and

your address and I will send you a dozen. US folks US dollars and Canadian
folks CDN dollars, as this will cover the higher postage rate to the USA.

These are only for the Rebel though TTBOMKnowledge, so Keith I'm not sure

if

you need them. The washers themselves are about 2" OD with a 3/8 ID hole
that fits the hinge bushing perfectly. They are about 0.032/0.040 thick

and

made of nylon 6. You will never wear them out....OEM usage was the thrust
washer for TRW seatbelts, to keep the recoil spring from wearing thru the
Polypro case.

On the Rebel they are used between the hinge brackets and the
elevator/rudder spar tubes end plugs and the rivets holding the push pull
horns on. The rudder is absolutely critical as without the washer in place
the rivets will chew their way through the lower hinge bracket thanks to
gravity.

Cheers,
Wayne O'Shea
1516 Alvin Williams Rd
Penetanguishene, Ontario
L9M-2C1

----- Original Message -----
From: "Keith B. Oliver" <kb_oliver@verizon.net>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 11, 2005 4:22 PM
Subject: RE: nylon washers

I could use some also
Would be more than happy to pay for them
Thanks

Keith B. Oliver
ELITE N654ME (reserved)
Farmingdale, Maine

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
Wayne G. O'Shea
Sent: Monday, April 11, 2005 12:41 PM
To: rebel-builders@dcsol.com
Subject: Re: nylon washers

Jesse, did I not throw a dozen in of my thrust washers?? MAM used to

have

nothing there, then bought about 2000 from me and then switched to
something
inferior in my mind. Give me your mailing address again and I send you
some.
Wayne

----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 11, 2005 11:36 AM
Subject: nylon washers

Where do you get the nylon washers called for in the elevator/rudder
hinge?
I didn't get any with my kit. Are they an AN part, or hardware store?
Thanks.
Jesse

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:24 am**

Do they sit on top of the rivets in the horn end plug, or do you cut down
the outside diameter on that one so they go inside the rivets?

From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
Reply-To: <rebel-builders@dcsol.com>
To: <rebel-builders@dcsol.com>
Subject: Re: nylon washers
Date: Tue, 12 Apr 2005 21:48:30 -0400

BTW, the exact dimensions for those that may have a need, OD = 1.85". ID
hole = 0.3985" and thickness is 0.042"

Wayne

----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 11, 2005 7:38 PM
Subject: Re: nylon washers

Jesse bought a whole airplane kit from me and why I said I'd send him
some
N/C......

As previously posted......anyone that wants them just send me $5 >CASH<
and
your address and I will send you a dozen. US folks US dollars and
Canadian
folks CDN dollars, as this will cover the higher postage rate to the
USA.
These are only for the Rebel though TTBOMKnowledge, so Keith I'm not
sure
if
you need them. The washers themselves are about 2" OD with a 3/8 ID hole
that fits the hinge bushing perfectly. They are about 0.032/0.040 thick
and
made of nylon 6. You will never wear them out....OEM usage was the
thrust
washer for TRW seatbelts, to keep the recoil spring from wearing thru
the
Polypro case.

On the Rebel they are used between the hinge brackets and the
elevator/rudder spar tubes end plugs and the rivets holding the push
pull
horns on. The rudder is absolutely critical as without the washer in
place
the rivets will chew their way through the lower hinge bracket thanks to
gravity.

Cheers,
Wayne O'Shea
1516 Alvin Williams Rd
Penetanguishene, Ontario
L9M-2C1

----- Original Message -----
From: "Keith B. Oliver" <kb_oliver@verizon.net>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 11, 2005 4:22 PM
Subject: RE: nylon washers

I could use some also
Would be more than happy to pay for them
Thanks

Keith B. Oliver
ELITE N654ME (reserved)
Farmingdale, Maine

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
Wayne G. O'Shea
Sent: Monday, April 11, 2005 12:41 PM
To: rebel-builders@dcsol.com
Subject: Re: nylon washers

Jesse, did I not throw a dozen in of my thrust washers?? MAM used to
have
nothing there, then bought about 2000 from me and then switched to
something
inferior in my mind. Give me your mailing address again and I send you
some.
Wayne

----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 11, 2005 11:36 AM
Subject: nylon washers

hinge?
store?

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:24 am**

The main idea is to keep those rivets from wearing through your hinge
bracket...so YES they get left full size to cover the rivets.

----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: <rebel-builders@dcsol.com>
Sent: Tuesday, April 12, 2005 10:15 PM
Subject: Re: nylon washers

Do they sit on top of the rivets in the horn end plug, or do you cut down
the outside diameter on that one so they go inside the rivets?

From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
Reply-To: <rebel-builders@dcsol.com>
To: <rebel-builders@dcsol.com>
Subject: Re: nylon washers
Date: Tue, 12 Apr 2005 21:48:30 -0400

BTW, the exact dimensions for those that may have a need, OD = 1.85". ID
hole = 0.3985" and thickness is 0.042"

Wayne

----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 11, 2005 7:38 PM
Subject: Re: nylon washers

Jesse bought a whole airplane kit from me and why I said I'd send him
some
N/C......

As previously posted......anyone that wants them just send me $5
CASH<
and
your address and I will send you a dozen. US folks US dollars and
Canadian
folks CDN dollars, as this will cover the higher postage rate to the
USA.
These are only for the Rebel though TTBOMKnowledge, so Keith I'm not
sure
if
you need them. The washers themselves are about 2" OD with a 3/8 ID

hole

that fits the hinge bushing perfectly. They are about 0.032/0.040

thick

and
made of nylon 6. You will never wear them out....OEM usage was the
thrust
washer for TRW seatbelts, to keep the recoil spring from wearing thru
the
Polypro case.

On the Rebel they are used between the hinge brackets and the
elevator/rudder spar tubes end plugs and the rivets holding the push
pull
horns on. The rudder is absolutely critical as without the washer in
place
the rivets will chew their way through the lower hinge bracket thanks

to

gravity.

Cheers,
Wayne O'Shea
1516 Alvin Williams Rd
Penetanguishene, Ontario
L9M-2C1

----- Original Message -----
From: "Keith B. Oliver" <kb_oliver@verizon.net>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 11, 2005 4:22 PM
Subject: RE: nylon washers

have
something

you

some.

elevator/rudder

store?

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:24 am**

Thanks,
I thought maybe you could use a couple to get above the rivets, but that's
easier.
Jesse

From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
Reply-To: <rebel-builders@dcsol.com>
To: <rebel-builders@dcsol.com>
Subject: Re: nylon washers
Date: Tue, 12 Apr 2005 22:22:29 -0400

The main idea is to keep those rivets from wearing through your hinge
bracket...so YES they get left full size to cover the rivets.

----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: <rebel-builders@dcsol.com>
Sent: Tuesday, April 12, 2005 10:15 PM
Subject: Re: nylon washers

Do they sit on top of the rivets in the horn end plug, or do you cut
down
the outside diameter on that one so they go inside the rivets?

From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
Reply-To: <rebel-builders@dcsol.com>
To: <rebel-builders@dcsol.com>
Subject: Re: nylon washers
Date: Tue, 12 Apr 2005 21:48:30 -0400

BTW, the exact dimensions for those that may have a need, OD = 1.85".
ID
hole = 0.3985" and thickness is 0.042"

Wayne

----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <rebel-builders@dcsol.com>
Sent: Monday, April 11, 2005 7:38 PM
Subject: Re: nylon washers

him
some
CASH<
and Canadian USA. sure
if
hole
thick
and thrust
thru
the pull place
thanks
to
Of
to
have
you
elevator/rudder
store?
-----------------------------------------------------------------
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:27 am**

Dale, Dave and Keith...your washers hit the mail box this morning. Let me
know when they arrive oifa@irishfield.on.ca

Wayne

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

The Murphy Builders Site

nylon washers

nylon washers

nylon washers

nylon washers

nylon washers

nylon washers

nylon washers

nylon washers

nylon washers

Nylon Washers