The Murphy Builders Site

Posted: **Sat Feb 18, 2012 10:13 am**

Hello All,
we have started to work on the project, Any of you have bright ideas
regarding thr routing of the cable(underneath the floor) or possibly some
other good ideas
cheers
gilles e717

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:13 am**

Gilles ... we should be building the flap control (floor mounted) system in
the next few weeks. Think the cable will run with the elevator cables (on
top of the floor), then up from a pulley behind the aft cabin bulkhead, then
forward from another pulley to a carry thru flap tube. The cable run
(elevators and flap) will have a shroud over them to protect from cargo (and
people). This could change ... but that's the idea as of today.
Bob e612

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
Gilles St-Pierre
Sent: Wednesday, February 23, 2005 7:45 PM
To: rebel-builders@dcsol.com
Subject: RE:Elite floor mounted flap handle

Hello All,
we have started to work on the project, Any of you have bright ideas
regarding thr routing of the cable(underneath the floor) or possibly some
other good ideas
cheers
gilles e717

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:13 am**

Hi Bob !

Maybe both of you should have a look at how Wayne did his setup.
I think there are photos on his website somewhere -
www.irishfield.on.ca

or maybe he will re-post them to the archives - they were there !

I think he ran a shaft out to the left side, and then a pushrod back
to a bellcrank to raise the standard bar that mounts the aileron bellcrank.
The floor mount was fairly far forward, just behind the big tube for the
sticks, so the shaft could run parallel to the tube, out to the left, I think.
OR - maybe you could just use a teleflex cable behind the seat and up....

.......bobp

-------------------------------orig.-------------------------
On Wednesday 23 February 2005 10:47 pm, Bob Andrews wrote:

Gilles ... we should be building the flap control (floor mounted) system in
the next few weeks. Think the cable will run with the elevator cables (on
top of the floor), then up from a pulley behind the aft cabin bulkhead, then
forward from another pulley to a carry thru flap tube. The cable run
(elevators and flap) will have a shroud over them to protect from cargo (and
people). This could change ... but that's the idea as of today.
Bob e612

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
Gilles St-Pierre
Sent: Wednesday, February 23, 2005 7:45 PM
To: rebel-builders@dcsol.com
Subject: RE:Elite floor mounted flap handle

Hello All,
we have started to work on the project, Any of you have bright ideas
regarding thr routing of the cable(underneath the floor) or possibly some
other good ideas
cheers
gilles e717

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:13 am**

https://www.dcsol.com/file/area216/Hyd% ... ation2.jpg

https://www.dcsol.com/file/area216/Hyd% ... lation.jpg

----- Original Message -----
From: "Bob Patterson" <beep@sympatico.ca>
To: <rebel-builders@dcsol.com>
Sent: Wednesday, February 23, 2005 11:05 PM
Subject: Re: Elite floor mounted flap handle

Hi Bob !

Maybe both of you should have a look at how Wayne did his setup.
I think there are photos on his website somewhere -
www.irishfield.on.ca

or maybe he will re-post them to the archives - they were there !

I think he ran a shaft out to the left side, and then a pushrod back
to a bellcrank to raise the standard bar that mounts the aileron

bellcrank.

The floor mount was fairly far forward, just behind the big tube for the
sticks, so the shaft could run parallel to the tube, out to the left, I

think.

OR - maybe you could just use a teleflex cable behind the seat and up....

.......bobp

-------------------------------orig.-------------------------
On Wednesday 23 February 2005 10:47 pm, Bob Andrews wrote:
Gilles ... we should be building the flap control (floor mounted) system

in

the next few weeks. Think the cable will run with the elevator cables

(on

top of the floor), then up from a pulley behind the aft cabin bulkhead,

then

forward from another pulley to a carry thru flap tube. The cable run
(elevators and flap) will have a shroud over them to protect from cargo

(and

people). This could change ... but that's the idea as of today.
Bob e612

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
Gilles St-Pierre
Sent: Wednesday, February 23, 2005 7:45 PM
To: rebel-builders@dcsol.com
Subject: RE:Elite floor mounted flap handle

Hello All,
we have started to work on the project, Any of you have bright ideas
regarding thr routing of the cable(underneath the floor) or possibly

some

other good ideas
cheers
gilles e717

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:13 am**

Thanks Wayne ... I LIKE IT. Should have material to work with from the old
roof mounted system. Notices there's two notches of reflex ... how much
speed does it buy you?

Bob e612

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
Wayne G. O'Shea
Sent: Wednesday, February 23, 2005 9:28 PM
To: rebel-builders@dcsol.com
Subject: Re: Elite floor mounted flap handle

https://www.dcsol.com/file/area216/Hyd% ... ation2.jpg

https://www.dcsol.com/file/area216/Hyd% ... lation.jpg

----- Original Message -----
From: "Bob Patterson" <beep@sympatico.ca>
To: <rebel-builders@dcsol.com>
Sent: Wednesday, February 23, 2005 11:05 PM
Subject: Re: Elite floor mounted flap handle

Hi Bob !

Maybe both of you should have a look at how Wayne did his setup.
I think there are photos on his website somewhere -
www.irishfield.on.ca

or maybe he will re-post them to the archives - they were there !

I think he ran a shaft out to the left side, and then a pushrod back
to a bellcrank to raise the standard bar that mounts the aileron

bellcrank.

The floor mount was fairly far forward, just behind the big tube for the
sticks, so the shaft could run parallel to the tube, out to the left, I

think.

OR - maybe you could just use a teleflex cable behind the seat and up....

.......bobp

-------------------------------orig.-------------------------
On Wednesday 23 February 2005 10:47 pm, Bob Andrews wrote:
Gilles ... we should be building the flap control (floor mounted) system

in

the next few weeks. Think the cable will run with the elevator cables

(on

top of the floor), then up from a pulley behind the aft cabin bulkhead,

then

forward from another pulley to a carry thru flap tube. The cable run
(elevators and flap) will have a shroud over them to protect from cargo

(and

people). This could change ... but that's the idea as of today.
Bob e612

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
Gilles St-Pierre
Sent: Wednesday, February 23, 2005 7:45 PM
To: rebel-builders@dcsol.com
Subject: RE:Elite floor mounted flap handle

Hello All,
we have started to work on the project, Any of you have bright ideas
regarding thr routing of the cable(underneath the floor) or possibly

some

other good ideas
cheers
gilles e717

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:13 am**

Hi Wayne !

This is strange - I get an error saying

Posted: **Sat Feb 18, 2012 10:13 am**

Wonder if you need to be signed into the builders site first? Anybody else
have a problem clicking and not getting anything.

Wayne

----- Original Message -----
From: "Bob Patterson" <beep@sympatico.ca>
To: <rebel-builders@dcsol.com>
Sent: Thursday, February 24, 2005 11:15 AM
Subject: Re: Elite floor mounted flap handle

[quote]

Hi Wayne !

This is strange - I get an error saying

Posted: **Sat Feb 18, 2012 10:13 am**

I down loaded two very nice pictures with no problems.

Thanks Wayne
Lonnie

----- Original Message -----
From: "Bob Patterson" <beep@sympatico.ca>
To: <rebel-builders@dcsol.com>
Sent: Thursday, February 24, 2005 11:15 AM
Subject: Re: Elite floor mounted flap handle

[quote]

Hi Wayne !

This is strange - I get an error saying

Posted: **Sat Feb 18, 2012 10:13 am**

Hi Wayne
I got in . Just had to sign in
Dale

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sat Feb 18, 2012 10:13 am**

I can answer that myself as I just tried...you have to sign in as I clicked
the link and it asked for my password etc.

Wayne
----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <rebel-builders@dcsol.com>
Sent: Thursday, February 24, 2005 11:26 AM
Subject: Re: Elite floor mounted flap handle

[quote]Wonder if you need to be signed into the builders site first? Anybody else
have a problem clicking and not getting anything.

Wayne

----- Original Message -----
From: "Bob Patterson" <beep@sympatico.ca>
To: <rebel-builders@dcsol.com>
Sent: Thursday, February 24, 2005 11:15 AM
Subject: Re: Elite floor mounted flap handle

[quote]

Hi Wayne !

This is strange - I get an error saying

Posted: **Sat Feb 18, 2012 10:13 am**

Ditto on the login ...

Wayne, from the flap handle lateral tube that goes to the left side, did you
go aft from the horn with a pushrod or Teleflex (along side the aileron
pushrod)... to the mixer? Also, I was wondering where to mount the hand
pump for the gear ... not any more, looks real good right there next to the
flap handle ... :-))

Bob e612

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
Wayne G. O'Shea
Sent: Thursday, February 24, 2005 9:32 AM
To: rebel-builders@dcsol.com
Subject: Re: Elite floor mounted flap handle

I can answer that myself as I just tried...you have to sign in as I clicked
the link and it asked for my password etc.

Wayne
----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <rebel-builders@dcsol.com>
Sent: Thursday, February 24, 2005 11:26 AM
Subject: Re: Elite floor mounted flap handle

[quote]Wonder if you need to be signed into the builders site first? Anybody else
have a problem clicking and not getting anything.

Wayne

----- Original Message -----
From: "Bob Patterson" <beep@sympatico.ca>
To: <rebel-builders@dcsol.com>
Sent: Thursday, February 24, 2005 11:15 AM
Subject: Re: Elite floor mounted flap handle

[quote]

Hi Wayne !

This is strange - I get an error saying

Posted: **Sat Feb 18, 2012 10:13 am**

Feb 2005 17:21:42 -0500

Hi Wayne
I got in . Just had to sign in
Dale

got in too. good engineering...!
gilles
e717>

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------