The Murphy Builders Site

Bob, Off the subject, but do you know Bill Kingston?
Thank You
Bobby Sather

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
Bob Patterson
Sent: Wednesday, January 26, 2005 12:38 PM
To: rebel-builders@dcsol.com
Subject: Re: deburring


Hi John !

Definitely the fastest way to deburr - but best only on inside
surfaces,
as the scuff marks will show on the outside, even through paint.

......bobp

-------------------------------orig.-------------------------

On Wednesday 26 January 2005 01:38 pm, John Kramer wrote:

I've been using a scotchbrite wheel on a drill which seems to smooth

the

holes fast and easy. Is this a bad idea?

John...

At 12:20 PM 01/26/05, you wrote:

be careful using this deburing tool that is spring loaded and does

both

sides of material
yes it works great when it works but as it is used and gets dirty or
slightly bent it jams an then cuts a hole to big for a 1/8 rivet, i

had

this happen and had to use alot of 5/32 rivets on some parts, but

when it

work good it was great just watch it very closely or you have

problems

and you may not notice till you go to rivet
can be purchased at aircraft tool supply company for 79.95, here is

link

to page, called two-way deburring toll #td001

http://www.aircraft-tool.com/shop/searc ... x?PageNo=3
mike#007

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of

Al

Paxhia
Sent: Wednesday, January 26, 2005 1:13 PM
To: rebel-builders@dcsol.com
Subject: Re: deburring


I did top and bottom holes and would recommend it. There is a slick
deburing

tool that has a spring loaded cutter, debur the top, push it through

and

debur the bottom. Ill dig around and find the source (I got mine from
Boeing

Surplus several years ago).
Al
Moose, N526AP
----- Original Message -----
From: <mbetti@up.net>
To: <rebel-builders@dcsol.com>
Sent: Wednesday, January 26, 2005 5:52 AM
Subject: deburring

on

learn

size

is

them

air

skins

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

----------------------------------------------------------------------

NOTICE - This message is the property of HATCH. It may also be
confidential and/or privileged. If you are not the intended

recipient

of this message you are hereby notified that you must not

disseminate,

copy or take any action with respect to it.

If you have received this message in error please notify
HATCH immediately via mailto:MailAdmin@hatch.ca.



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fly too low or too slow and the ground will rise up and smite thee.






-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Bob, Off the subject, but do you know Bill Kingston?
Thank You
Bobby Sather

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
Bob Patterson
Sent: Wednesday, January 26, 2005 12:38 PM
To: rebel-builders@dcsol.com
Subject: Re: deburring


Hi John !

Definitely the fastest way to deburr - but best only on inside
surfaces,
as the scuff marks will show on the outside, even through paint.

......bobp

-------------------------------orig.-------------------------

On Wednesday 26 January 2005 01:38 pm, John Kramer wrote:

I've been using a scotchbrite wheel on a drill which seems to smooth

the

holes fast and easy. Is this a bad idea?

John...

At 12:20 PM 01/26/05, you wrote:

be careful using this deburing tool that is spring loaded and does

both

sides of material
yes it works great when it works but as it is used and gets dirty

slightly bent it jams an then cuts a hole to big for a 1/8 rivet, i

had

this happen and had to use alot of 5/32 rivets on some parts, but

when it

work good it was great just watch it very closely or you have

problems

and you may not notice till you go to rivet
can be purchased at aircraft tool supply company for 79.95, here

link

to page, called two-way deburring toll #td001

http://www.aircraft-tool.com/shop/searc ... x?PageNo=3
mike#007

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf

Al

Paxhia
Sent: Wednesday, January 26, 2005 1:13 PM
To: rebel-builders@dcsol.com
Subject: Re: deburring


I did top and bottom holes and would recommend it. There is a slick
deburing

tool that has a spring loaded cutter, debur the top, push it

and

debur the bottom. Ill dig around and find the source (I got mine

Boeing

Surplus several years ago).
Al
Moose, N526AP
----- Original Message -----
From: <mbetti@up.net>
To: <rebel-builders@dcsol.com>
Sent: Wednesday, January 26, 2005 5:52 AM
Subject: deburring

on

learn

size

is

them

air

skins

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

----------------------------------------------------------------------

NOTICE - This message is the property of HATCH. It may also be
confidential and/or privileged. If you are not the intended

recipient

of this message you are hereby notified that you must not

disseminate,

copy or take any action with respect to it.

If you have received this message in error please notify
HATCH immediately via mailto:MailAdmin@hatch.ca.



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fly too low or too slow and the ground will rise up and smite thee.






-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

No, He built a custom coach, in fact the award winning coach of 2001 for
gentleman by the name of Bob Patterson. Just wondered if you were the
lucky man. Anyway I hope to start my Rebel Moose in the spring.
Britt Reed has got my pulse fired up. So hope to start as soon as the
weather breaks.

Good Luck to you
Bobby Sather
St George Utah

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
Bob Patterson
Sent: Wednesday, January 26, 2005 2:23 PM
To: rebel-builders@dcsol.com
Subject: Bill Kingston?


Name doesn ring any bells - but I meet soooo many people !
Where would I have met him ?? Is he building ?

......bobp

-------------------------------orig.-------------------------

On Wednesday 26 January 2005 02:49 pm, Bobby Sather wrote:

Bob, Off the subject, but do you know Bill Kingston?
Thank You
Bobby Sather

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
Bob Patterson
Sent: Wednesday, January 26, 2005 12:38 PM
To: rebel-builders@dcsol.com
Subject: Re: deburring


Hi John !

Definitely the fastest way to deburr - but best only on inside
surfaces,
as the scuff marks will show on the outside, even through paint.

......bobp

-------------------------------orig.-------------------------

On Wednesday 26 January 2005 01:38 pm, John Kramer wrote:

I've been using a scotchbrite wheel on a drill which seems to smooth

the

holes fast and easy. Is this a bad idea?

John...

At 12:20 PM 01/26/05, you wrote:

both

or

had

when it

problems

is

link

Of

Al

through

and

from

something

on

learn

final

size

and

is

it

over

them

fast

air

the

skins

-----------------------------------------------------------------

-----------------------------------------------------------------

----------------------------------------------------------------------

recipient

disseminate,

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fly too low or too slow and the ground will rise up and smite thee.






-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------