Thanks Ken.
Yes they will fit if you put the nuts on the inside for one of the sides.
I was concerned about doing that because MAM is very specific about the heads
of the bolts going to the inside.
Just a note, I do search the archives before I tackle each stage and it's
amazing the knowledge and help thats on this list.
Brad (R195)
bhewlett@omni-techsys.com
On 11/6/2004 2:55 PM,
KLEHMAN@ALBEDO.NET wrote to REBEL-BUILDERS:
-> Received: by dcsol.com (Wildcat! SMTP Router v6.0.451.3)
-> for
rebel-builders@dcsol.com; Sat, 06 Nov 2004 14:48:50 -0900
-> Received: from juliet.albedo.net ([206.51.22.2]) EHLO=juliet.albedo.net
-> by dcsol.com (Wildcat! SMTP v6.0.451.3) with SMTP
-> id 110823875; Sat, 06 Nov 2004 14:48:48 -0900
-> Received: from albedo.net (ppp168.albedo.net [206.51.22.168])
-> (authenticated bits=0)
-> by juliet.albedo.net (8.12.11/8.12.3) with ESMTP id iA6NmiEF022477
-> for <
rebel-builders@dcsol.com>; Sat, 6 Nov 2004 18:48:45 -0500
-> Message-ID: <
418D6473.40703@albedo.net>
-> Date: Sat, 06 Nov 2004 18:55:31 -0500
-> From: Ken <
klehman@albedo.net>
-> User-Agent: Mozilla/5.0 (Windows; U; Win98; en-US; rv:1.0.2)
Gecko/20021120 Netscape/7.01
-> X-Accept-Language: en-us, en
-> X-Orig-MIME-Version: 1.0
-> To:
rebel-builders@dcsol.com
-> Subject: Re: Tailspring Support
-> References: <
1099769823@dcsol.com>
-> X-Orig-Content-Type: text/plain; charset=us-ascii; format=flowed
-> X-Orig-Content-Transfer-Encoding: 7bit
-> X-Virus-Scanned: ClamAV 0.80/565/Sat Oct 30 09:31:13 2004
-> clamav-milter version 0.80j
-> on juliet.albedo.net
-> X-Virus-Status: Clean
-> X-Antivirus-Remover: Message filtered with wsAV v2.0.0 Build 001
->
-> Brad
-> OK, found the reference. I remember this has come up before so there is
-> something in the archives. It's hazy for me but I think some folks said
-> they had no problem. Some might have put the bolts on at least one side
-> with the nuts in the middle?? As long as you can still get the vertical
-> tailspring bolt in I don't see why it would matter which way the bolts
-> go in...
-> Ken
->
->
brad@dcsol.com wrote:
->
-> >Ken,
-> >
-> >Sorry,
-> >
-> >It's a Rebel.
-> >
-> >Brad
-> >
bhewlett@omni-techsys.com
-> >
-> >>
brad@dcsol.com wrote:
-> >->
-> >-> >Help...
-> >-> >
-> >-> >This my sound silly but acording to MAM's instructions (page 42)
-> >-> >Fus 85 and Fus 87 are supposed to be bolted together with four AN3-5A
-> >bolts
-> >-> >bach to back with the heads of the bolts on the inside.
-> >-> >
-> >-> >As near as I can figure there is no way to fit these bolts in to the
FUS-
-> >87
-> >-> >Any Suggestions?
-> >-> >
-> >-> >Thanks,
-> >-> >
-> >-> >Brad.
-> >-> >
bhewlett@omni-techsys.com
-> >
-> >
->
->
-----------------------------------------------------------------
List archives located at:
https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe:
rebel-builders-unsubscribe@dcsol.com
List administrator:
mike.davis@dcsol.com
-----------------------------------------------------------------