Moose Hartzell Prop
Posted: Sat Feb 18, 2012 9:16 am
Oops, it's actually 97" !! Here's the link to the Hartzell site on this
prop:
http://www.hartzellprop.com/kitplane/ki ... manufactur
er=Murphy%20SR2500
Maybe I just need to change the front wheels from 8.5" to larger <grin>
Ted
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
Bob Patterson
Sent: Monday, May 24, 2004 6:28 PM
To: murphy-rebel@dcsol.com
Subject: Re: Tailwheel / prop clearance
Hi Ted !
92 " sounds like a lot for a 3 blade on the Moose -
is that the diameter that Hartzell recommends ?? I seem to recall that
the 2 blade paddle was 9 feet - 108". Would have thought that a 3 blade
would be a lot shorter ...
In any case, there wasn't a big problem with clearance with the 9 ft.
paddle - although I was a bit nervous about raising the tail
too far the first few times ! ;-) So you should be fine with a
larger tailwheel.
.....bobp
----------------------------orig.-------------------
On Monday 24 May 2004 07:54 pm, you wrote:
--*
*-----------------------------------------------------------------------
--*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-----------------------------------------------------------------------
--*
*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
prop:
http://www.hartzellprop.com/kitplane/ki ... manufactur
er=Murphy%20SR2500
Maybe I just need to change the front wheels from 8.5" to larger <grin>
Ted
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
Bob Patterson
Sent: Monday, May 24, 2004 6:28 PM
To: murphy-rebel@dcsol.com
Subject: Re: Tailwheel / prop clearance
Hi Ted !
92 " sounds like a lot for a 3 blade on the Moose -
is that the diameter that Hartzell recommends ?? I seem to recall that
the 2 blade paddle was 9 feet - 108". Would have thought that a 3 blade
would be a lot shorter ...
In any case, there wasn't a big problem with clearance with the 9 ft.
paddle - although I was a bit nervous about raising the tail
too far the first few times ! ;-) So you should be fine with a
larger tailwheel.
.....bobp
----------------------------orig.-------------------
On Monday 24 May 2004 07:54 pm, you wrote:
18" is for a Moose, 92" Hartzell 3-blade prop, stopped on the ground
with the std MAM tailwheel. I'm just thinking of how the prop
clearance is reduced during takeoff (pushing the tail up a bit as one
gets going) and during any sort of a wheel landing. A hangar mate has
*-----------------------------------------------------------------------a 185 with a 3-blade and his prop clearance was (I think) 24" (or
more).
Thanks,
Ted
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
Legeorgen@aol.com
Sent: Monday, May 24, 2004 5:47 PM
To: murphy-rebel@dcsol.com
Subject: Re: Tailwheel / prop clearance
Ted,
Rebel or a Moose? 18" sounds like a lot even for a Moose. Did you
measure it in a flight level attitude?
I have a Rebel 0320 with a Scott 3200 tailwheel and It handles very
well. I never even unwrapped the MAM tailwheel form its plastic.
Bruce
*---------------------------------------------------------------------
--
--*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*
*---------------------------------------------------------------------
----*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
--*
*-----------------------------------------------------------------------
--*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-----------------------------------------------------------------------
--*
*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------