The Murphy Builders Site

C/S nutplates! How many THOUSAND would you like Ralph??

I have them with c/s for the rivets..... as well as the screw!

) Wayne

----- Original Message -----
From: "Ralph Baker" <rebaker@ftc-i.net>
To: <murphy-rebel@dcsol.com>
Sent: Thursday, April 22, 2004 10:24 AM
Subject: tool kit

At one time I think 120 degree puller dimplers were available but can't
now be found.
Wicks has the 120 degree microstop cutters as part ATS-120-40 for 3/32"
pulled rivets.
Cleaveland has 120 degree dimple dies for 1/8" pulled rivets as part
DIECS4-4.
Aircraft Spruce and Wicks both claim their 3/32" pull dimplers will work
for both bucked and pulled rivets.

Most places you can squeeze AD426 3/32" solid rivets where needed.
Those impossible places are mostly nut plates and the exact dimple angle
is not critical in my opinion.

While I'm at it Just Plane Hardware (formerly Freeman Aviation) has
hardware such as countersunk nutplates that I have trouble finding
elsewhere.

Ralph Baker
Elite 624E

*-------------------------------------------------------------------------*

To unsubscribe from this list go to:
http://www.dcsol.com:81/public/code/html-subscribe.wcx
Archives located at http://www.dcsol.com:81/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
http://www.dcsol.com:81/public/code/html-subscribe.wcx
Archives located at http://www.dcsol.com:81/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Before I get too many more emails for C/S nutplates I should clarify what I
have...now that I went out and refreshed my memory of what's on the 4' wide
x 8' high shelving unit of nutplates.

In 8-32 the only thing I have is stamped NAS-681-A08's (fixed) and Sturdy
old AN373-F832 fixed Nytrol (20,000+ of these ones!). These, both, only have
the screw hole C/S and not the rivet holes.

The only ones I have with the rivet holes C/S are 10-32 - AN373-F1032 fixed
Nytrol units and these have the screw hole C/S as well. I also have these
with just the screw hole C/S in both steel and aluminum.

Regards,
Wayne



----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <murphy-rebel@dcsol.com>
Sent: Thursday, April 22, 2004 11:51 AM
Subject: C/S nutplates

C/S nutplates! How many THOUSAND would you like Ralph??

I have them with c/s for the rivets..... as well as the screw!

) Wayne

*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
http://www.dcsol.com:81/public/code/html-subscribe.wcx
Archives located at http://www.dcsol.com:81/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------