The Murphy Builders Site

For builders of Murphy Aircraft Manufacturing kits - Bringing builders together
https://www.murphybuilders.net/

DUAL BRAKE

https://www.murphybuilders.net/viewtopic.php?f=1&t=3874

Page 1 of 1

DUAL BRAKE

Posted: Sat Feb 18, 2012 9:05 am
by Jean Poirier
When I ordered my rebel kit, I did'nt ordered the dual brake kit.
But now I think it will be a good idea to have dual (no time yet on tail wheel). MAM list the dual kit at $375.00 usd. In the manual, the plan show the plan/instruction for dual retrofit or single set of brake pedal. The only difference I can see, is just couple of tube, small brachets, cotter pin, bolt etc.... The $375.00 is like a warning light to me.... do I missed something? If not, I will fabricate thoses parts and save....
I am building a Rebel but I know someone wuo is building a Elite, do they have the same brakes pedal? If it is the same, I can use his parts for copy? Someone cant hel me..... I am waithing the firts inspection (tail, aileron) and I want to finish those parts (final rivething, trim installation) before to start the wings. So if it is too long, I will make the brake parts until.

Jean
Rebel 747R



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

DUAL BRAKE

Posted: Sat Feb 18, 2012 9:05 am
by klehman
Hi Jean
Yet another option is to pick up a cheap set of used brake cylinders at
Sun&FUN and make two extra brake pedals. Either way I think "airparts"
in the flymarket usually has cheap short lengths of 4130 tubing but they
may sell out by later in the week. I picked up a parking brake valve as
well. There was no visible wear on the used parts so I put new buna
o-rings in them and installed them. They will get removed when 119 goes
onto floats anyway. I haven't taken a good look at the mechanical
interconnect system to see which approach I like better or which is less
work.
Ken

Jean Poirier wrote:
When I ordered my rebel kit, I did'nt ordered the dual brake kit.
But now I think it will be a good idea to have dual (no time yet on tail wheel). MAM list the dual kit at $375.00 usd. In the manual, the plan show the plan/instruction for dual retrofit or single set of brake pedal. The only difference I can see, is just couple of tube, small brachets, cotter pin, bolt etc.... The $375.00 is like a warning light to me.... do I missed something? If not, I will fabricate thoses parts and save....
I am building a Rebel but I know someone wuo is building a Elite, do they have the same brakes pedal? If it is the same, I can use his parts for copy? Someone cant hel me..... I am waithing the firts inspection (tail, aileron) and I want to finish those parts (final rivething, trim installation) before to start the wings. So if it is too long, I will make the brake parts until.

Jean
Rebel 747R


*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

DUAL BRAKE

Posted: Sat Feb 18, 2012 9:09 am
by Wayne G. O'Shea
Jean.....the cheapest option (and probably the best working set up) is to go
to a salvage yard and get a full set of pedals out of a Cessna or
Beechcraft. The AULA Rebel that I am refurbing right now has a set, that I
believe came out of a Beechcraft, and they are the cats meow..... compared
to MAM's set up.

If you want some pics just ask!

Wayne

----- Original Message -----
From: "Jean Poirier" <oxyport@globetrotter.net>
To: <murphy-rebel@dcsol.com>
Sent: Monday, March 22, 2004 8:23 AM
Subject: DUAL BRAKE

When I ordered my rebel kit, I did'nt ordered the dual brake kit.
But now I think it will be a good idea to have dual (no time yet on tail
wheel). MAM list the dual kit at $375.00 usd. In the manual, the plan
show the plan/instruction for dual retrofit or single set of brake pedal.
The only difference I can see, is just couple of tube, small brachets,
cotter pin, bolt etc.... The $375.00 is like a warning light to me....
do I missed something? If not, I will fabricate thoses parts and save....
I am building a Rebel but I know someone wuo is building a Elite, do they
have the same brakes pedal? If it is the same, I can use his parts for
copy? Someone cant hel me..... I am waithing the firts inspection (tail,
aileron) and I want to finish those parts (final rivething, trim
installation) before to start the wings. So if it is too long, I will make
the brake parts until.
Jean
Rebel 747R



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

DUAL BRAKE

Posted: Sat Feb 18, 2012 9:09 am
by Jean Poirier
Hi Wayne!

Cessna parts.... just for the right side or for both side... Complete
with cylinder and everything or just the pedal?
Thank'

Jean
p.s.: will you be at Sun'fun..... I will be there with a builder of Laval
who is building a Elite very slowly! (it is a subliminal message for him
......)

----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <murphy-rebel@dcsol.com>
Sent: Tuesday, March 23, 2004 10:16 AM
Subject: Re: DUAL BRAKE

Jean.....the cheapest option (and probably the best working set up) is to
go
to a salvage yard and get a full set of pedals out of a Cessna or
Beechcraft. The AULA Rebel that I am refurbing right now has a set, that I
believe came out of a Beechcraft, and they are the cats meow..... compared
to MAM's set up.

If you want some pics just ask!

Wayne

----- Original Message -----
From: "Jean Poirier" <oxyport@globetrotter.net>
To: <murphy-rebel@dcsol.com>
Sent: Monday, March 22, 2004 8:23 AM
Subject: DUAL BRAKE

When I ordered my rebel kit, I did'nt ordered the dual brake kit.
But now I think it will be a good idea to have dual (no time yet on
tail
wheel). MAM list the dual kit at $375.00 usd. In the manual, the plan
show the plan/instruction for dual retrofit or single set of brake pedal.
The only difference I can see, is just couple of tube, small brachets,
cotter pin, bolt etc.... The $375.00 is like a warning light to me....
do I missed something? If not, I will fabricate thoses parts and
save....
I am building a Rebel but I know someone wuo is building a Elite, do
they
have the same brakes pedal? If it is the same, I can use his parts for
copy? Someone cant hel me..... I am waithing the firts inspection (tail,
aileron) and I want to finish those parts (final rivething, trim
installation) before to start the wings. So if it is too long, I will
make
the brake parts until.
Jean
Rebel 747R



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*
*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*




*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

DUAL BRAKE

Posted: Sat Feb 18, 2012 9:09 am
by Jean Poirier
Wayne...
yes some picks.....

Jean
----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <murphy-rebel@dcsol.com>
Sent: Tuesday, March 23, 2004 10:16 AM
Subject: Re: DUAL BRAKE

Jean.....the cheapest option (and probably the best working set up) is to
go
to a salvage yard and get a full set of pedals out of a Cessna or
Beechcraft. The AULA Rebel that I am refurbing right now has a set, that I
believe came out of a Beechcraft, and they are the cats meow..... compared
to MAM's set up.

If you want some pics just ask!

Wayne

----- Original Message -----
From: "Jean Poirier" <oxyport@globetrotter.net>
To: <murphy-rebel@dcsol.com>
Sent: Monday, March 22, 2004 8:23 AM
Subject: DUAL BRAKE

When I ordered my rebel kit, I did'nt ordered the dual brake kit.
But now I think it will be a good idea to have dual (no time yet on
tail
wheel). MAM list the dual kit at $375.00 usd. In the manual, the plan
show the plan/instruction for dual retrofit or single set of brake pedal.
The only difference I can see, is just couple of tube, small brachets,
cotter pin, bolt etc.... The $375.00 is like a warning light to me....
do I missed something? If not, I will fabricate thoses parts and
save....
I am building a Rebel but I know someone wuo is building a Elite, do
they
have the same brakes pedal? If it is the same, I can use his parts for
copy? Someone cant hel me..... I am waithing the firts inspection (tail,
aileron) and I want to finish those parts (final rivething, trim
installation) before to start the wings. So if it is too long, I will
make
the brake parts until.
Jean
Rebel 747R



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*
*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*




*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

DUAL BRAKE

Posted: Sat Feb 18, 2012 9:09 am
by Wayne G. O'Shea
Jean...take the entire assembly! Pedals/cylinders/mounting blocks and all
for dual control. There's usually only one set of cylinders on a nice set...
that are operated by pushing either sides pedals. Using double sets of
cylinders plumbed in series only adds to the cost/maintenance/leak
possibilities.

Cheers,
Wayne

----- Original Message -----
From: "Jean Poirier" <oxyport@globetrotter.net>
To: <murphy-rebel@dcsol.com>
Sent: Tuesday, March 23, 2004 12:09 PM
Subject: Re: DUAL BRAKE

Hi Wayne!

Cessna parts.... just for the right side or for both side... Complete
with cylinder and everything or just the pedal?
Thank'

Jean
p.s.: will you be at Sun'fun..... I will be there with a builder of Laval
who is building a Elite very slowly! (it is a subliminal message for him
......)

----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <murphy-rebel@dcsol.com>
Sent: Tuesday, March 23, 2004 10:16 AM
Subject: Re: DUAL BRAKE

Jean.....the cheapest option (and probably the best working set up) is
to
go
to a salvage yard and get a full set of pedals out of a Cessna or
Beechcraft. The AULA Rebel that I am refurbing right now has a set, that
I
believe came out of a Beechcraft, and they are the cats meow.....
compared
to MAM's set up.

If you want some pics just ask!

Wayne

----- Original Message -----
From: "Jean Poirier" <oxyport@globetrotter.net>
To: <murphy-rebel@dcsol.com>
Sent: Monday, March 22, 2004 8:23 AM
Subject: DUAL BRAKE

When I ordered my rebel kit, I did'nt ordered the dual brake kit.
But now I think it will be a good idea to have dual (no time yet on
tail
wheel). MAM list the dual kit at $375.00 usd. In the manual, the
plan
show the plan/instruction for dual retrofit or single set of brake
pedal.
The only difference I can see, is just couple of tube, small brachets,
cotter pin, bolt etc.... The $375.00 is like a warning light to me....
do I missed something? If not, I will fabricate thoses parts and
save....
I am building a Rebel but I know someone wuo is building a Elite, do
they
have the same brakes pedal? If it is the same, I can use his parts for
copy? Someone cant hel me..... I am waithing the firts inspection
(tail,
aileron) and I want to finish those parts (final rivething, trim
installation) before to start the wings. So if it is too long, I will
make
the brake parts until.
Jean
Rebel 747R



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*
*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*
*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://www.dcsol.com/default.htm
Archives public username "rebel" password "builder"
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
All times are UTC-09:00
Page 1 of 1
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/