Stol Kit & Hoerner wing tips
Posted: Sat Feb 18, 2012 12:04 am
Thanks Bob, here is the standard information that I reply to builders with.
I currently produce 4 different parts that fit the Murphy Rebel. Hoerner Wing tips, 560.00 per pair, Hoerner Wing tips with landing/recognition lights and lens 630.00, Rudder and elevator tips (set of 3) 120.00, and flaperon control rod fairing, 25.00 set of 2.
All funds are in U.S. Shipping is an additional cost depending on location.
Parts are made to fit and very little is necessary to complete the installation.
Delivery is approximately a 6 week lead time. I require 50% as down payment and the balance prior to delivery.
The Hoerner tips have shown to do the following: lower stall by 2 MPH, increase cruise by 2 MPH, reduce ground roll by 50' and add stability in slow flight.
All parts will save you lots of building time, approximately 80 hrs for all parts.
Should you have additional questions, note me back.
Thanks for the inquiry.
Bob Patterson <apat@istar.ca> wrote:
Hi Alister !
Not on their sales staff - just passing on the word about
products i've used & like ! (You should hear me on some of the
things I like !!! ;-) - - no, I guess I can't talk
about those too much ... might upset a lot of listeners who've
bought them !)
Anyway, you can catch Dave Fife at:
(for Hoerner wing & tail tips, aileron pushrod fairings, etc.)
aircrafttips@yahoo.com
If you catch up to Dave, maybe you could ask him to please
post here the original performance improvement numbers that he & Curt
got from their test flying, as I've forgotten the exact numbers !
And Angus McKenzie at:
(for the STOL leading edge & wing fence kits)
"Angus McKenzie - McKenzie/STOL"
Both will be positive additions for performance & safety,
and now, with your (and our) improved dollar positions, not quite
as painful as they were last year !! ;-)
......bobp
--------------------------------orig.----------------------------
At 05:03 PM 12/6/03 +1300, you wrote:
3D Composite Aircraft Parts Inc.
1345 Merkle St.
Ortonville, MI. 48462
Phone 248-627-4367
www.stormpages.com/3dcomposite/
Long EZ in progress, Cozy IV, #888,on hold.
---------------------------------
Do you Yahoo!?
Protect your identity with Yahoo! Mail AddressGuard
*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
I currently produce 4 different parts that fit the Murphy Rebel. Hoerner Wing tips, 560.00 per pair, Hoerner Wing tips with landing/recognition lights and lens 630.00, Rudder and elevator tips (set of 3) 120.00, and flaperon control rod fairing, 25.00 set of 2.
All funds are in U.S. Shipping is an additional cost depending on location.
Parts are made to fit and very little is necessary to complete the installation.
Delivery is approximately a 6 week lead time. I require 50% as down payment and the balance prior to delivery.
The Hoerner tips have shown to do the following: lower stall by 2 MPH, increase cruise by 2 MPH, reduce ground roll by 50' and add stability in slow flight.
All parts will save you lots of building time, approximately 80 hrs for all parts.
Should you have additional questions, note me back.
Thanks for the inquiry.
Bob Patterson <apat@istar.ca> wrote:
Hi Alister !
Not on their sales staff - just passing on the word about
products i've used & like ! (You should hear me on some of the
things I like !!! ;-) - - no, I guess I can't talk
about those too much ... might upset a lot of listeners who've
bought them !)
Anyway, you can catch Dave Fife at:
(for Hoerner wing & tail tips, aileron pushrod fairings, etc.)
aircrafttips@yahoo.com
If you catch up to Dave, maybe you could ask him to please
post here the original performance improvement numbers that he & Curt
got from their test flying, as I've forgotten the exact numbers !
And Angus McKenzie at:
(for the STOL leading edge & wing fence kits)
"Angus McKenzie - McKenzie/STOL"
Both will be positive additions for performance & safety,
and now, with your (and our) improved dollar positions, not quite
as painful as they were last year !! ;-)
......bobp
--------------------------------orig.----------------------------
At 05:03 PM 12/6/03 +1300, you wrote:
David K. FifeAll this talk about STOL kits and Fife wing tips has got me all keen to find
out a little more ( nice sales job Bob), but I am unable to find contact
numbers. Can anyone help me please.
Cheers
Alister
3D Composite Aircraft Parts Inc.
1345 Merkle St.
Ortonville, MI. 48462
Phone 248-627-4367
www.stormpages.com/3dcomposite/
Long EZ in progress, Cozy IV, #888,on hold.
---------------------------------
Do you Yahoo!?
Protect your identity with Yahoo! Mail AddressGuard
*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------