flush avex rivet

[Jean Poirier]

I am fixing the brass bushing across the end plate ( and horn) on the aileron. Murphy ask to contersink with a grind 1/2' drill but they do not specifid the rivets angle! I have use a microstop contersing cutter for solid rivet (100 deg.) It looks ok but is it? what is the degree for those Avex flush rivet?

Thanks

Jean Poirier
Rebel 747R



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Wayne G. O'Shea]

The Avex RV44's are actually 118 to 120 degrees, but the 100 c/s is pretty
close and I have to admit that I've cheated a >few< times!
Wayne

----- Original Message -----
From: "Jean Poirier" <oxyport@globetrotter.net>
To: <murphy-rebel@dcsol.com>
Sent: Thursday, December 04, 2003 11:07 AM
Subject: flush avex rivet

I am fixing the brass bushing across the end plate ( and horn) on the

aileron. Murphy ask to contersink with a grind 1/2' drill but they do not
specifid the rivets angle! I have use a microstop contersing cutter for
solid rivet (100 deg.) It looks ok but is it? what is the degree for those
Avex flush rivet?

Thanks

Jean Poirier
Rebel 747R

*-------------------------------------------------------------------------*

To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[klehman]

Jean

120 degree countersinks are available in single flute and multi-flute
from tool suppliers but the ones that I have do not have a mandrel and
are not self centering. However a normal 118 degree drill bit will
finish the countersink a little better than just a 100 degree cutter and
help you get a flush surface after you rivet.

120 degrees seems to be common for non aviation blind rivets including
avex, pop, and the structural Q rivets.

Ken

Wayne G. O'Shea wrote:

The Avex RV44's are actually 118 to 120 degrees, but the 100 c/s is pretty
close and I have to admit that I've cheated a >few< times!
Wayne

----- Original Message -----
From: "Jean Poirier" <oxyport@globetrotter.net>
To: <murphy-rebel@dcsol.com>
Sent: Thursday, December 04, 2003 11:07 AM
Subject: flush avex rivet

I am fixing the brass bushing across the end plate ( and horn) on the

aileron. Murphy ask to contersink with a grind 1/2' drill but they do not
specifid the rivets angle! I have use a microstop contersing cutter for
solid rivet (100 deg.) It looks ok but is it? what is the degree for those
Avex flush rivet?

Thanks

*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[goody]

I have 120' countersinks with centering mandrels from Brown tool.
Jim
----- Original Message -----
From: <klehman@albedo.net>
To: <murphy-rebel@dcsol.com>
Sent: Thursday, December 04, 2003 12:43 PM
Subject: Re: flush avex rivet

Jean

120 degree countersinks are available in single flute and multi-flute
from tool suppliers but the ones that I have do not have a mandrel and
are not self centering. However a normal 118 degree drill bit will
finish the countersink a little better than just a 100 degree cutter and
help you get a flush surface after you rivet.

120 degrees seems to be common for non aviation blind rivets including
avex, pop, and the structural Q rivets.

Ken

Wayne G. O'Shea wrote:

The Avex RV44's are actually 118 to 120 degrees, but the 100 c/s is

pretty

close and I have to admit that I've cheated a >few< times!
Wayne

----- Original Message -----
From: "Jean Poirier" <oxyport@globetrotter.net>
To: <murphy-rebel@dcsol.com>
Sent: Thursday, December 04, 2003 11:07 AM
Subject: flush avex rivet

I am fixing the brass bushing across the end plate ( and horn) on the

aileron. Murphy ask to contersink with a grind 1/2' drill but they do

not

specifid the rivets angle! I have use a microstop contersing cutter for
solid rivet (100 deg.) It looks ok but is it? what is the degree for

those

Avex flush rivet?

Thanks

*-------------------------------------------------------------------------*

To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------