The Murphy Builders Site

Just a progress report. I finally have positioned and drilled the seat
rails. What a great feeling to sit inside and make engine noises. Next is
making some access plates and running the elevator cables.

Scott Hibbs
hibbs@pacifier.com



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Hello Scott

Although I'v put my cable guides in place we're at the same stage. I used 7
guides on each side for the rudder and 14 down the middle for the elevator
cables. May seem like overkill but I wanted to take as much slop out of the
cables as possible.

Good luck, lets keep at it.

Murray Cherkas
REBEL 505
C-GKNN

Where do live?




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Murray, did you find that you had too much binding with the 14 guides? More
is better unless the extra friction is too noticable. I live in Vancouver, WA
(near Portland, OR).

Scott

->
-> Hello Scott
->
-> Although I'v put my cable guides in place we're at the same stage. I used 7
-> guides on each side for the rudder and 14 down the middle for the elevator
-> cables. May seem like overkill but I wanted to take as much slop out of the
-> cables as possible.
->
-> Good luck, lets keep at it.
->
-> Murray Cherkas
-> REBEL 505
-> C-GKNN
->
-> Where do live?
->





-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Hi Scott:

The 14 guides up the centre,7 for each cable.
If installed according to the manual I felt they would rub. There is a high
point at bulkhead F so I put one at the high point. The manual also shows
one about 18" in front of the pulleys at the end of the floor. I felt that
the cables would sag here and rub on the floor so I put one just in front of
the pulleys.The first guide aft of the control column results in quite a
change of direction so I put this 1st guide a little further back. The rest
of the guides hold the cable up in the event of a little slack in the cable.
This I hope will allow me to not make the cable so tight. The longer the
distance between guides the tighter the cable has to be to prevent a
sagging cable rubbing the floor. I don't think there is any more friction
with more guides as they are all straight with no side friction.

Good luck
Murray Cherkas
REBEL 505




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Hi Scott

I may be comming that way in July and would like to stop by and see your
rebel if you might not mind.

Lets keep in touch.

Murray Cherkas
REBEL 505




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Murray, that would be great. My home number is 360-546-0389.

Scott


-> Hi Scott
->
-> I may be comming that way in July and would like to stop by and see your
-> rebel if you might not mind.
->
-> Lets keep in touch.
->
-> Murray Cherkas
-> REBEL 505
->





-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------