The Murphy Builders Site

I used a 2" sanding disk on my drill.. I used this methor for deburring about
1/2 of the holes in the kit..

Dave
SR#057

moose2b@dcsol.com wrote:

Just finished drilling out all the holes in my stab stringers - I'm looking
for suggestions on how to deburr the backside. My deburring tool won't fit
into the holes squarely because of the "J" hook. My first idea was to sand the
burrs off, but I'll be sanding into the next year at the rate I got the first
few done. I sure hope someone has a better idea!!

Thanks,

Terry Riedel


*-------------------------------------------------------------------------*
To unsubscribe go to http://www.dcsol.com:81/public/listserv.htm
Archives located at http://rebel:builder@www.dcsol.com:81/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

On the inside, just run a small flat file down the length of the stringers
(a few times) and then check the holes for any small burrs that bent over
into the holes and hand run a drill though any that have to knock them off.

Regards,
Wayne G.O'Shea
www.irishfield.on.ca

----- Original Message -----
From: <moose2b@dcsol.com>
To: <murphy-rebel@dcsol.com>
Sent: Monday, April 22, 2002 1:26 PM
Subject: wing and horizontal stab stringers

Just finished drilling out all the holes in my stab stringers - I'm

looking

for suggestions on how to deburr the backside. My deburring tool won't fit
into the holes squarely because of the "J" hook. My first idea was to sand

the

burrs off, but I'll be sanding into the next year at the rate I got the

first

few done. I sure hope someone has a better idea!!

Thanks,

Terry Riedel

*-------------------------------------------------------------------------*

To unsubscribe go to http://www.dcsol.com:81/public/listserv.htm
Archives located at http://rebel:builder@www.dcsol.com:81/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Just finished drilling out all the holes in my stab stringers - I'm looking
for suggestions on how to deburr the backside. My deburring tool won't fit
into the holes squarely because of the "J" hook. My first idea was to sand the
burrs off, but I'll be sanding into the next year at the rate I got the first
few done. I sure hope someone has a better idea!!

Thanks,

Terry Riedel




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

I used a Dremel tool with the cut-off disk attachment.
I then held the tool upside down and ran the disk over
the holes at a very flat angle to 'sand' the burrs
off. Was quick and easy to manoeuvre.

-Jason

--- moose2b@dcsol.com wrote:

Just finished drilling out all the holes in my stab
stringers - I'm looking
for suggestions on how to deburr the backside. My
deburring tool won't fit
into the holes squarely because of the "J" hook. My
first idea was to sand the
burrs off, but I'll be sanding into the next year at
the rate I got the first
few done. I sure hope someone has a better idea!!

Thanks,

Terry Riedel

*-------------------------------------------------------------------------*

To unsubscribe go to
http://www.dcsol.com:81/public/listserv.htm
Archives located at
http://rebel:builder@www.dcsol.com:81/default.htm
To contact the list admin, e-mail
mike.davis@dcsol.com

*-------------------------------------------------------------------------*


=====
________________________________________________

Jason Beall
Super Rebel No. 131
Aberdeen, Scotland, UK
super_rebel131@yahoo.com

__________________________________________________
Do You Yahoo!?
Yahoo! Games - play chess, backgammon, pool and more
http://games.yahoo.com/



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Terry

I took a fine file. This is a hard place to get at.

Good Luck

Murray Cherkas
REBEL505




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Hi Terry I've been using a die grinder with a 2" scotchbrite pad. It's the
same tool that I use for roughing up mating surfaces before joining on my
floats.
Drew Dalgleish

At 09:26 AM 4/22/2002 -0800, you wrote:

Just finished drilling out all the holes in my stab stringers - I'm looking
for suggestions on how to deburr the backside. My deburring tool won't fit
into the holes squarely because of the "J" hook. My first idea was to sand

the

burrs off, but I'll be sanding into the next year at the rate I got the

first

few done. I sure hope someone has a better idea!!

Thanks,

Terry Riedel


*-------------------------------------------------------------------------*
To unsubscribe go to http://www.dcsol.com:81/public/listserv.htm
Archives located at http://rebel:builder@www.dcsol.com:81/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*

-----------------------------------------------------





-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------