The Murphy Builders Site

"She" sure looks close to completion Al!!!! Can smell that engine running
already!

Wayne



----- Original Message -----
From: "Al & Deb Paxhia" <paxhia2@attbi.com>
To: <murphy-rebel@dcsol.com>
Sent: Friday, February 08, 2002 7:32 PM
Subject: Re: SR3500 - Fus705 to 310 bolts and float attachment

Mike,
I have uploaded a photo in the SR fuselage section, the only one handy.

If

you look close you can see the belly wrap and float brackets.
Al
----- Original Message -----
From: "Mike Davis" <mike.davis@dcsol.com>
To: <murphy-rebel@dcsol.com>
Sent: Thursday, February 07, 2002 10:39 PM
Subject: Re: SR3500 - Fus705 to 310 bolts and float attachment

This sounds like a good candidate for a photo to be uploaded. I for one
would like to see how/where you cut your slots. I for one think the
prototype looks like it's got a big hole in the side the way it is done

now.

Mike
195SR

----- Original Message -----
From: "Al & Deb Paxhia" <paxhia2@attbi.com>
To: <murphy-rebel@dcsol.com>
Sent: Thursday, February 07, 2002 7:55 PM
Subject: Re: SR3500 - Fus705 to 310 bolts and float attachment

Hi Wayne,
The wrap for the belly (don't have the part # handy) on the 3500

upgrade

is

cut in half for installation. I had Murphy roll the part so it fits

tight

to

the sill. Also when cutting the gear leg slot and FL400's we made

three

slots, two for the float attach brackets and one for the gear leg.

Murphy

used a large rectangle that when it pulled up around the sill is looks

like

it gaps and bends rather sharp. Rolling eliminates the fit problem and

the

slots look clean enough that I don't need a cover over the gear leg or

the

float brackets.
Al
MOOOOSE#26
----- Original Message -----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
To: <murphy-rebel@dcsol.com>
Sent: Thursday, February 07, 2002 4:54 PM
Subject: SR3500 - Fus705 to 310 bolts and float attachment

drilled

with

bolts

in

exact

is

just

slip

back

pilot

hole.

for

bolt

before

I

triangle

by

anyone

while

later.

I

so

**

itself

**

http://rebel:builder@www.dcsol.com:81/default.htm

** **


** To unsubscribe, send e-mail to list-server@dcsol.com with

**

** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself

**

** Archives located at

http://rebel:builder@www.dcsol.com:81/default.htm

**

** To contact the list admin, e-mail mike.davis@dcsol.com

**


** To unsubscribe, send e-mail to list-server@dcsol.com with

**

** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself

**

** Archives located at http://rebel:builder@www.dcsol.com:81/default.htm

**

** To contact the list admin, e-mail mike.davis@dcsol.com

**


** To unsubscribe, send e-mail to list-server@dcsol.com with

**

** UNSUBSCRIBE MURPHY-REBEL in the message body on a line by itself

**

** Archives located at http://rebel:builder@www.dcsol.com:81/default.htm

**

** To contact the list admin, e-mail mike.davis@dcsol.com

**




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------