crap spreading bolts
Posted: Fri Feb 17, 2012 4:22 pm
Received: from az.com (seawesta-69.az.com [204.201.18.69])
by lucy.az.com (8.8.5/8.8.5) with ESMTP id XAA20923;
Mon, 31 Aug 1998 23:12:52 -0700 (PDT)
Message-ID: <35EB91B2.FF9C2CB2@az.com>
Date: Mon, 31 Aug 1998 23:18:30 -0700
From: Dan Morehouse <morehous@az.com>
Reply-To: morehous@az.com
X-Mailer: Mozilla 4.05 (Macintosh; I; PPC)
MIME-Version: 1.0
To: murtech <murtech@murphyair.com>, murphy-rebel <murphy-rebel@dcsol.com>
Subject: crap spreading bolts
Content-Type: multipart/alternative;
boundary="------------790C904505FFED266851198A"
--------------790C904505FFED266851198A
Content-Type: text/plain; charset=us-ascii; x-mac-type="54455854";
x-mac-creator="4D4F5353"
Content-Transfer-Encoding: 7bit
Hello Dennis!
Earlier you suggested that I "DON'T SPREAD CRAP LIKE THIS AROUND"
regarding construction of the Rebel cage without bolts.Thank you so much
for the clarification. You must have meant using no temporary bolts in
constructing the cage. But if this is again a misunderstanding, please
feel free to use any type of vocabulary you wish in guiding me to the
truth :-)
So there are three AN3-20A bolts that go in end of the bottom part of
the cage. What are the complete AN numbers for the 5/16" bolts, the
washers and nuts that go a few inches to the center of these 3/16"
bolts? My manual says only 5/16" bolt (no AN designation). And when are
these permanently installed?
Thank you for your time,
Dan Morehouse
R280
--------------790C904505FFED266851198A
Content-Type: text/html; charset=us-ascii
Content-Transfer-Encoding: 7bit
<HTML>
Hello Dennis!
<P>Earlier you suggested that I "DON'T SPREAD CRAP LIKE THIS AROUND"
regarding
construction of the Rebel cage without bolts.Thank you so much for the
clarification. You must have meant using no <I>temporary</I> bolts in
constructing
the cage. But if this is again a misunderstanding, please feel free to
use any type of vocabulary you wish in guiding me to the truth :-)
<P>So there are three AN3-20A bolts that go in end of the bottom part of
the cage. What are the complete AN numbers for the 5/16" bolts, the washers
and nuts that go a few inches to the center of these 3/16" bolts? My manual
says only 5/16" bolt (no AN designation). And when are these permanently
installed?
<P>Thank you for your time,
<BR>Dan Morehouse
<BR>R280</HTML>
--------------790C904505FFED266851198A--
by lucy.az.com (8.8.5/8.8.5) with ESMTP id XAA20923;
Mon, 31 Aug 1998 23:12:52 -0700 (PDT)
Message-ID: <35EB91B2.FF9C2CB2@az.com>
Date: Mon, 31 Aug 1998 23:18:30 -0700
From: Dan Morehouse <morehous@az.com>
Reply-To: morehous@az.com
X-Mailer: Mozilla 4.05 (Macintosh; I; PPC)
MIME-Version: 1.0
To: murtech <murtech@murphyair.com>, murphy-rebel <murphy-rebel@dcsol.com>
Subject: crap spreading bolts
Content-Type: multipart/alternative;
boundary="------------790C904505FFED266851198A"
--------------790C904505FFED266851198A
Content-Type: text/plain; charset=us-ascii; x-mac-type="54455854";
x-mac-creator="4D4F5353"
Content-Transfer-Encoding: 7bit
Hello Dennis!
Earlier you suggested that I "DON'T SPREAD CRAP LIKE THIS AROUND"
regarding construction of the Rebel cage without bolts.Thank you so much
for the clarification. You must have meant using no temporary bolts in
constructing the cage. But if this is again a misunderstanding, please
feel free to use any type of vocabulary you wish in guiding me to the
truth :-)
So there are three AN3-20A bolts that go in end of the bottom part of
the cage. What are the complete AN numbers for the 5/16" bolts, the
washers and nuts that go a few inches to the center of these 3/16"
bolts? My manual says only 5/16" bolt (no AN designation). And when are
these permanently installed?
Thank you for your time,
Dan Morehouse
R280
--------------790C904505FFED266851198A
Content-Type: text/html; charset=us-ascii
Content-Transfer-Encoding: 7bit
<HTML>
Hello Dennis!
<P>Earlier you suggested that I "DON'T SPREAD CRAP LIKE THIS AROUND"
regarding
construction of the Rebel cage without bolts.Thank you so much for the
clarification. You must have meant using no <I>temporary</I> bolts in
constructing
the cage. But if this is again a misunderstanding, please feel free to
use any type of vocabulary you wish in guiding me to the truth :-)
<P>So there are three AN3-20A bolts that go in end of the bottom part of
the cage. What are the complete AN numbers for the 5/16" bolts, the washers
and nuts that go a few inches to the center of these 3/16" bolts? My manual
says only 5/16" bolt (no AN designation). And when are these permanently
installed?
<P>Thank you for your time,
<BR>Dan Morehouse
<BR>R280</HTML>
--------------790C904505FFED266851198A--