The Murphy Builders Site

The list archives are located at:
http://www.dcsol.com:81/public/default.htm
username: rebel password: builder

Hello Folks

Has anyone building a tri-gear (Elite or SR) installed the MAM supplied

light kit? Did you change the angle it is mounted to accomodate the

ground attitude of the tri-gear?

We are about to do the mounting and other than making the guess that until

the light needs to be oriented the same (one of the 2 lamps) but in

taxi things will be different. Perhaps there is enough adjustment in the

holders that it doesn't matter?

All MAM was able to suggest was that the lights will have to be aimed
differently since it is a tri-gear. They had no info on installation of

except to state that it was designed to fit the taildragger Rebel (since

time no tri-gears were available)...........................

Your suggestions?

Thanks

Dave R.

--
David A. Ricker P. Eng.
DARTEC Engineering Inc.
Fall River, Nova Scotia
Canada

You have received this message because you have subscribed to the
murphy-rebel mailing list.
To unsubscribe from this list, send an e-mail to: list-server@dcsol.com
with "unsubscribe murphy-rebel" in the body of the message.
For assistance contact mike.davis@dcsol.com

*-------------------------------------------------------------------------*
The list archives are located at:
http://www.dcsol.com:81/public/default.htm
username: rebel password: builder
*-------------------------------------------------------------------------*
Dave

Hal Edmonson is building an SR for tri-gear, and at present he is mounting
his landing lights (Trevor Yaworski originals).
He plans to move the top flange back about 1 1/2".
He's not in the newsgroup, but you can get ahold of him at 905-623-7488.

Rick

----- Original Message -----
From: David Ricker <ricker@dbis.ns.ca>
To: <murphy-rebel@dcsol.com>
Sent: Tuesday, May 01, 2001 11:21 PM
Subject: Landing Light Installation in a Tri-Gear

*-------------------------------------------------------------------------*

The list archives are located at:
http://www.dcsol.com:81/public/default.htm
username: rebel password: builder

*-------------------------------------------------------------------------*

Hello Folks

Has anyone building a tri-gear (Elite or SR) installed the MAM supplied

landing

light kit? Did you change the angle it is mounted to accomodate the

different

ground attitude of the tri-gear?

We are about to do the mounting and other than making the guess that until

flare

the light needs to be oriented the same (one of the 2 lamps) but in

touchdown &

taxi things will be different. Perhaps there is enough adjustment in the

lamp

holders that it doesn't matter?

All MAM was able to suggest was that the lights will have to be aimed
differently since it is a tri-gear. They had no info on installation of

the kit

except to state that it was designed to fit the taildragger Rebel (since

at that

time no tri-gears were available)...........................

Your suggestions?

Thanks

Dave R.

--
David A. Ricker P. Eng.
DARTEC Engineering Inc.
Fall River, Nova Scotia
Canada

*-------------------------------------------------------------------------*

You have received this message because you have subscribed to the
murphy-rebel mailing list.
To unsubscribe from this list, send an e-mail to: list-server@dcsol.com
with "unsubscribe murphy-rebel" in the body of the message.
For assistance contact mike.davis@dcsol.com

*-------------------------------------------------------------------------*

*-------------------------------------------------------------------------*
You have received this message because you have subscribed to the
murphy-rebel mailing list.
To unsubscribe from this list, send an e-mail to: list-server@dcsol.com
with "unsubscribe murphy-rebel" in the body of the message.
For assistance contact mike.davis@dcsol.com
*-------------------------------------------------------------------------*

*-------------------------------------------------------------------------*
The list archives are located at:
http://www.dcsol.com:81/public/default.htm
username: rebel password: builder
*-------------------------------------------------------------------------*
Rick

Thanks for the lead.

Moving the top flange back that far seems like a lot doesn't it? FWIW, I
haven't cut metal on this yet but I am toying with leaving it where the
instructions call for and using the built in adjustment, can anyone comment on
how much adjustment is left (to account for the Tri-Gear attitude vs tailwheel)
when the lights are set up for a taildragger?

Thanks

Dave R.

Rick and Cathy Ford wrote:

*-------------------------------------------------------------------------*
The list archives are located at:
http://www.dcsol.com:81/public/default.htm
username: rebel password: builder
*-------------------------------------------------------------------------*
Dave

Hal Edmonson is building an SR for tri-gear, and at present he is mounting
his landing lights (Trevor Yaworski originals).
He plans to move the top flange back about 1 1/2".
He's not in the newsgroup, but you can get ahold of him at 905-623-7488.

Rick

----- Original Message -----
From: David Ricker <ricker@dbis.ns.ca>
To: <murphy-rebel@dcsol.com>
Sent: Tuesday, May 01, 2001 11:21 PM
Subject: Landing Light Installation in a Tri-Gear

*-------------------------------------------------------------------------*

The list archives are located at:
http://www.dcsol.com:81/public/default.htm
username: rebel password: builder

*-------------------------------------------------------------------------*

Hello Folks

Has anyone building a tri-gear (Elite or SR) installed the MAM supplied

landing

light kit? Did you change the angle it is mounted to accomodate the

different

ground attitude of the tri-gear?

We are about to do the mounting and other than making the guess that until

flare

the light needs to be oriented the same (one of the 2 lamps) but in

touchdown &

taxi things will be different. Perhaps there is enough adjustment in the

lamp

holders that it doesn't matter?

All MAM was able to suggest was that the lights will have to be aimed
differently since it is a tri-gear. They had no info on installation of

the kit

except to state that it was designed to fit the taildragger Rebel (since

at that

time no tri-gears were available)...........................

Your suggestions?

Thanks

Dave R.

--
David A. Ricker P. Eng.
DARTEC Engineering Inc.
Fall River, Nova Scotia
Canada

*-------------------------------------------------------------------------*

You have received this message because you have subscribed to the
murphy-rebel mailing list.
To unsubscribe from this list, send an e-mail to: list-server@dcsol.com
with "unsubscribe murphy-rebel" in the body of the message.
For assistance contact mike.davis@dcsol.com

*-------------------------------------------------------------------------*

*-------------------------------------------------------------------------*
You have received this message because you have subscribed to the
murphy-rebel mailing list.
To unsubscribe from this list, send an e-mail to: list-server@dcsol.com
with "unsubscribe murphy-rebel" in the body of the message.
For assistance contact mike.davis@dcsol.com
*-------------------------------------------------------------------------*

--
David A. Ricker P. Eng.
DARTEC Engineering Inc.
3 Tamarac Drive
Fall River, Nova Scotia
Canada, B2T 1E8
ricker@dbis.ns.ca
Ph. 902-860-0256


*-------------------------------------------------------------------------*
You have received this message because you have subscribed to the
murphy-rebel mailing list.
To unsubscribe from this list, send an e-mail to: list-server@dcsol.com
with "unsubscribe murphy-rebel" in the body of the message.
For assistance contact mike.davis@dcsol.com
*-------------------------------------------------------------------------*

*-------------------------------------------------------------------------*
The list archives are located at:
http://www.dcsol.com:81/public/default.htm
username: rebel password: builder
*-------------------------------------------------------------------------*
Received: from rossine.total.net ([154.11.89.167])
by dcsol.com (wcSMTP v5.4.449.4)
with SMTP id 266285015; Tue, 08 May 2001 03:28:43 -0800
Received: (qmail 20480 invoked from network); 8 May 2001 13:56:04 -0000
Received: from unknown (HELO ip241.toronto76.dialup.canada.psi.net) (154.20.70.241)
by smtp.total.net with SMTP; 8 May 2001 13:56:04 -0000
X-Sender: crs1188@209.89.75.25
X-Mailer: Windows Eudora Light Version 1.5.2
Mime-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
To: <murphy-rebel@dcsol.com>
From: Bob Patterson <bob.patterson@canrem.com>
Subject: Re: Landing Light Installation in a Tri-Gear

Hi Dave !

You are likely OK to just follow the instructions. There's
lots of adjustment there. We had the same situation going from
taildragger to amphibs - no problem.

.....bobp

---------------------------------orig.------------------------------------
At 10:57 PM 5/7/01 -0300, you wrote:

*-------------------------------------------------------------------------*
The list archives are located at:
http://www.dcsol.com:81/public/default.htm
username: rebel password: builder
*-------------------------------------------------------------------------*
Rick

Thanks for the lead.

Moving the top flange back that far seems like a lot doesn't it? FWIW, I
haven't cut metal on this yet but I am toying with leaving it where the
instructions call for and using the built in adjustment, can anyone comment on
how much adjustment is left (to account for the Tri-Gear attitude vs tailwheel)
when the lights are set up for a taildragger?

Thanks

Dave R.

Rick and Cathy Ford wrote:

*-------------------------------------------------------------------------*
The list archives are located at:
http://www.dcsol.com:81/public/default.htm
username: rebel password: builder
*-------------------------------------------------------------------------*
Dave

Hal Edmonson is building an SR for tri-gear, and at present he is mounting
his landing lights (Trevor Yaworski originals).
He plans to move the top flange back about 1 1/2".
He's not in the newsgroup, but you can get ahold of him at 905-623-7488.

Rick

----- Original Message -----
From: David Ricker <ricker@dbis.ns.ca>
To: <murphy-rebel@dcsol.com>
Sent: Tuesday, May 01, 2001 11:21 PM
Subject: Landing Light Installation in a Tri-Gear

*-------------------------------------------------------------------------* *-------------------------------------------------------------------------* landing different flare touchdown & lamp the kit at that *-------------------------------------------------------------------------* *-------------------------------------------------------------------------*

*-------------------------------------------------------------------------*
You have received this message because you have subscribed to the
murphy-rebel mailing list.
To unsubscribe from this list, send an e-mail to: list-server@dcsol.com
with "unsubscribe murphy-rebel" in the body of the message.
For assistance contact mike.davis@dcsol.com
*-------------------------------------------------------------------------*

--
David A. Ricker P. Eng.
DARTEC Engineering Inc.
3 Tamarac Drive
Fall River, Nova Scotia
Canada, B2T 1E8
ricker@dbis.ns.ca
Ph. 902-860-0256


*-------------------------------------------------------------------------*
You have received this message because you have subscribed to the
murphy-rebel mailing list.
To unsubscribe from this list, send an e-mail to: list-server@dcsol.com
with "unsubscribe murphy-rebel" in the body of the message.
For assistance contact mike.davis@dcsol.com
*-------------------------------------------------------------------------*

*-------------------------------------------------------------------------*
You have received this message because you have subscribed to the
murphy-rebel mailing list.
To unsubscribe from this list, send an e-mail to: list-server@dcsol.com
with "unsubscribe murphy-rebel" in the body of the message.
For assistance contact mike.davis@dcsol.com
*-------------------------------------------------------------------------*