The Murphy Builders Site

my skyview encodes and sends it......I had the radio shop do the
hook-ups. CW


On Thu, Jul 21, 2011 at 12:32 PM , Roland Kriening wrote:

I purchased a Garmin 327 Transponder at Sun n Fun, but did not get a
wiring
harness with it. Also did not buy an altitude encoder. If anyone has a
327
installed, could you let me know what you used as an encoder, and
where you
bought your wiring harness.

Roland
R56


-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Roland,
Try San Luis Avionics on Barnstormers
John



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Every transponder to encoder interface I've seen are a simple grey code ...
not too hard to wire up ... one wire at a time.

Bob 612e

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Roland
Kriening
Sent: Thursday, July 21, 2011 1:33 PM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Garmin 327 Transponder

I purchased a Garmin 327 Transponder at Sun n Fun, but did not get a wiring
harness with it. Also did not buy an altitude encoder. If anyone has a 327
installed, could you let me know what you used as an encoder, and where you
bought your wiring harness.

Roland
R56


-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

It is pretty much A1, A2, A4, B1, B2, B4, D1, D2, D4, power,
ground, on all the older type encoders

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Bob
Andrews
Sent: Thursday, July 21, 2011 10:20 PM
To: rebel-builders@dcsol.com
Subject: RE: [rebel-builders] Garmin 327 Transponder


Every transponder to encoder interface I've seen are a simple grey code ...
not too hard to wire up ... one wire at a time.

Bob 612e

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Roland
Kriening
Sent: Thursday, July 21, 2011 1:33 PM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Garmin 327 Transponder

I purchased a Garmin 327 Transponder at Sun n Fun, but did not get a wiring
harness with it. Also did not buy an altitude encoder. If anyone has a 327
installed, could you let me know what you used as an encoder, and where you
bought your wiring harness.

Roland
R56





-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login username "rebel"
password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------