The Murphy Builders Site

Marc,
I've had a lot of luck with small PVC (plumbing) tubes. I have
several of different sizes (length and diameter). If you can pick a corner
and get it started, then use the tube to wrap it around. The tube applies
more even pressure across the skin and it's not so hard on your fingers.
Even my more difficult coverings come off easier with the tubes.
Jerry Folkerts

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of
marc.van.hulzen@dcsol.com
Sent: Sunday, May 08, 2011 2:23 AM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] protection foil

Hello,

I've just finished the roof plate but there are difficulties with the
removal of
the protection foil. The foil is on the sheet for almost 15 years now.

I have tried paint remover, a paint stripper and several chemicals without
result.

Any suggestions will be appreciated.

Marc



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------







-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

I used a heat gun with very good results.

Gordon
----- Original Message -----
From: marc.van.hulzen@dcsol.com<mailto:marc.van.hulzen@dcsol.com>
To: rebel-builders@dcsol.com<mailto:rebel-builders@dcsol.com>
Sent: Sunday, May 08, 2011 1:22 AM
Subject: [rebel-builders] protection foil


Hello,

I've just finished the roof plate but there are difficulties with the removal of
the protection foil. The foil is on the sheet for almost 15 years now.

I have tried paint remover, a paint stripper and several chemicals without
result.

Any suggestions will be appreciated.

Marc



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login<https://ma ... .com/login>
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com<mailto:rebel-builders-unsubscribe@dcsol.com>
List administrator: mike.davis@dcsol.com<mailto:mike.davis@dcsol.com>
-----------------------------------------------------------------







-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Both lighter fluid and Goof Off have been recommended in the past.

Ron



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Ya, I know what you mean. I tried allkinds of guck too then, because
I was working in a fairly cool shop I

warmed the sheet up with a heat lamp and was able to increase the peel rate
immensly.

Hope this helps, Bob Elite 710




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Thank you all for your respond.
I'm going to check if the plate can resist my patience....

Marc

-----Oorspronkelijk bericht-----
Van: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] Namens Bob Bjorn
Verzonden: maandag 9 mei 2011 17:27
Aan: rebel-builders@dcsol.com
Onderwerp: Re: [rebel-builders] protection foil

Ya, I know what you mean. I tried allkinds of guck too then, because
I was working in a fairly cool shop I

warmed the sheet up with a heat lamp and was able to increase the peel rate
immensly.

Hope this helps, Bob Elite 710




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------