The Murphy Builders Site

For builders of Murphy Aircraft Manufacturing kits - Bringing builders together
https://www.murphybuilders.net/

[rebel-builders] carburator bits

https://www.murphybuilders.net/viewtopic.php?f=1&t=10989

Page 1 of 1

[rebel-builders] carburator bits

Posted: Sun Feb 19, 2012 6:23 pm
by walter.klatt
Garry, this is probably not your problem, but thought I would mention a situation I had once with my 320 carb. It is possible to install the bowl and have the mixture cut off out of position. I did that a long time when doing some troubleshooting, with the result being unable to properly shut off the fuel at the carb. Solution was simply to reinstall the bowl taking care to make sure the mixture goes into the right hole.

Walter
Sent on the TELUS Mobility network with BlackBerry

-----Original Message-----
From: Garry Wright <wright.garry30@gmail.com>
Date: Fri, 04 Jun 2010 10:39:29
To: <rebel-builders@dcsol.com>
Subject: [rebel-builders] carburator bits

I've got a Marvel-Schebler MA-4SPA part# 10-3678-12 on my O-320. I'm
having a bit of trouble with idle cutoff and it seems to be leak-by
associated with the mixture barrel/window-sleeve/window components. I
can't find the part numbers on this part - anyone know how to find same?
Reference EAA article by Richard Koehler "It Won't Shut Down".

Garry
C-FOKM



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] carburator bits

Posted: Sun Feb 19, 2012 6:23 pm
by wright.garry30
Interesting but weird. Bowl was not removed since I got it and mixture wrkd correctly so tt's likely not it. Tnx anyway.

G
Sent on the TELUS Mobility network with BlackBerry

-----Original Message-----
From: walter.klatt@shaw.ca
Date: Fri, 4 Jun 2010 17:11:54
To: <rebel-builders@dcsol.com>
Subject: Re: [rebel-builders] carburator bits

Garry, this is probably not your problem, but thought I would mention a situation I had once with my 320 carb. It is possible to install the bowl and have the mixture cut off out of position. I did that a long time when doing some troubleshooting, with the result being unable to properly shut off the fuel at the carb. Solution was simply to reinstall the bowl taking care to make sure the mixture goes into the right hole.

Walter
Sent on the TELUS Mobility network with BlackBerry

-----Original Message-----
From: Garry Wright <wright.garry30@gmail.com>
Date: Fri, 04 Jun 2010 10:39:29
To: <rebel-builders@dcsol.com>
Subject: [rebel-builders] carburator bits

I've got a Marvel-Schebler MA-4SPA part# 10-3678-12 on my O-320. I'm
having a bit of trouble with idle cutoff and it seems to be leak-by
associated with the mixture barrel/window-sleeve/window components. I
can't find the part numbers on this part - anyone know how to find same?
Reference EAA article by Richard Koehler "It Won't Shut Down".

Garry
C-FOKM



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] carburator bits

Posted: Sun Feb 19, 2012 6:23 pm
by Charlie Eubanks
Have you checked to see if your primer check valve is seated? It will
continue to run but rough after shutdown if leaking
Charlie E..
----- Original Message -----
From: "Garry Wright" <wright.garry30@gmail.com>
To: <rebel-builders@dcsol.com>
Sent: Friday, June 04, 2010 11:39 AM
Subject: [rebel-builders] carburator bits

I've got a Marvel-Schebler MA-4SPA part# 10-3678-12 on my O-320. I'm
having a bit of trouble with idle cutoff and it seems to be leak-by
associated with the mixture barrel/window-sleeve/window components. I
can't find the part numbers on this part - anyone know how to find same?
Reference EAA article by Richard Koehler "It Won't Shut Down".

Garry
C-FOKM



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] carburator bits

Posted: Sun Feb 19, 2012 6:23 pm
by walter.klatt
Or if there is some dirt in there not allowing it to seat properly. I had that problem once, too. It was actually Wayne here on this list that correctly diagnosed that one. My symptoms had to do with a rough running engine, though, not a problem shutting down.
Sent on the TELUS Mobility network with BlackBerry

-----Original Message-----
From: Charlie Eubanks <charlie@troyairpark.com>
Date: Fri, 04 Jun 2010 17:05:02
To: <rebel-builders@dcsol.com>
Subject: Re: [rebel-builders] carburator bits

Have you checked to see if your primer check valve is seated? It will
continue to run but rough after shutdown if leaking
Charlie E..
----- Original Message -----
From: "Garry Wright" <wright.garry30@gmail.com>
To: <rebel-builders@dcsol.com>
Sent: Friday, June 04, 2010 11:39 AM
Subject: [rebel-builders] carburator bits

I've got a Marvel-Schebler MA-4SPA part# 10-3678-12 on my O-320. I'm
having a bit of trouble with idle cutoff and it seems to be leak-by
associated with the mixture barrel/window-sleeve/window components. I
can't find the part numbers on this part - anyone know how to find same?
Reference EAA article by Richard Koehler "It Won't Shut Down".

Garry
C-FOKM



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] carburator bits

Posted: Sun Feb 19, 2012 6:23 pm
by Simon Smith
Gary,
The part # for the MA4SPA 10-3678-12 Mixture control metering valve assy. is
242-514 hope this helps.
Si
----- Original Message -----
From: "Garry Wright" <wright.garry30@gmail.com>
To: <rebel-builders@dcsol.com>
Sent: Friday, June 04, 2010 11:39 AM
Subject: [rebel-builders] carburator bits

I've got a Marvel-Schebler MA-4SPA part# 10-3678-12 on my O-320. I'm
having a bit of trouble with idle cutoff and it seems to be leak-by
associated with the mixture barrel/window-sleeve/window components. I
can't find the part numbers on this part - anyone know how to find same?
Reference EAA article by Richard Koehler "It Won't Shut Down".

Garry
C-FOKM



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------


--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.437 / Virus Database: 271.1.1/2917 - Release Date: 06/04/10
06:25:00




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] carburator bits

Posted: Sun Feb 19, 2012 6:23 pm
by Garry Wright
Thanks Si. That could help a lot. Where did you find that and who is a
good supplier?

Garry

On 10-06-04 06:40 PM, Simon Smith wrote:
Gary,
The part # for the MA4SPA 10-3678-12 Mixture control metering valve assy. is
242-514 hope this helps.
Si
----- Original Message -----
From: "Garry Wright"<wright.garry30@gmail.com>
To:<rebel-builders@dcsol.com>
Sent: Friday, June 04, 2010 11:39 AM
Subject: [rebel-builders] carburator bits


I've got a Marvel-Schebler MA-4SPA part# 10-3678-12 on my O-320. I'm
having a bit of trouble with idle cutoff and it seems to be leak-by
associated with the mixture barrel/window-sleeve/window components. I
can't find the part numbers on this part - anyone know how to find same?
Reference EAA article by Richard Koehler "It Won't Shut Down".

Garry
C-FOKM



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.437 / Virus Database: 271.1.1/2917 - Release Date: 06/04/10
06:25:00




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



--
Garry Wright

Skepticism is the highest duty and blind faith the one unpardonable sin.
-- Thomas Huxley, (attributed: source unknown)




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] carburator bits

Posted: Sun Feb 19, 2012 6:23 pm
by Garry Wright
Thanks Charlie. If I don't get anywhere with the thread I'm following I
will chase that one. The article below suggests that would cause plug
fouling and other problems before this cutoff issue so I'll keep it in mind.

Garry

On 10-06-04 04:05 PM, Charlie Eubanks wrote:
Have you checked to see if your primer check valve is seated? It will
continue to run but rough after shutdown if leaking
Charlie E..
----- Original Message -----
From: "Garry Wright"<wright.garry30@gmail.com>
To:<rebel-builders@dcsol.com>
Sent: Friday, June 04, 2010 11:39 AM
Subject: [rebel-builders] carburator bits


I've got a Marvel-Schebler MA-4SPA part# 10-3678-12 on my O-320. I'm
having a bit of trouble with idle cutoff and it seems to be leak-by
associated with the mixture barrel/window-sleeve/window components. I
can't find the part numbers on this part - anyone know how to find same?
Reference EAA article by Richard Koehler "It Won't Shut Down".

Garry
C-FOKM



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



--
Garry Wright

Skepticism is the highest duty and blind faith the one unpardonable sin.
-- Thomas Huxley, (attributed: source unknown)




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] carburator bits

Posted: Sun Feb 19, 2012 6:23 pm
by Simon Smith
Gary,
The information came from my Precision Carburetors Manual. I don't know of a
source right now but you might try A.E.R.O. 1-800-362-3044 or El Reno
Aviation 405-262-2387.
Si
----- Original Message -----
From: "Garry Wright" <wright.garry30@gmail.com>
To: <rebel-builders@dcsol.com>
Sent: Saturday, June 05, 2010 6:39 AM
Subject: Re: [rebel-builders] carburator bits

Thanks Si. That could help a lot. Where did you find that and who is a
good supplier?

Garry

On 10-06-04 06:40 PM, Simon Smith wrote:
Gary,
The part # for the MA4SPA 10-3678-12 Mixture control metering valve assy.
is
242-514 hope this helps.
Si
----- Original Message -----
From: "Garry Wright"<wright.garry30@gmail.com>
To:<rebel-builders@dcsol.com>
Sent: Friday, June 04, 2010 11:39 AM
Subject: [rebel-builders] carburator bits


I've got a Marvel-Schebler MA-4SPA part# 10-3678-12 on my O-320. I'm
having a bit of trouble with idle cutoff and it seems to be leak-by
associated with the mixture barrel/window-sleeve/window components. I
can't find the part numbers on this part - anyone know how to find same?
Reference EAA article by Richard Koehler "It Won't Shut Down".

Garry
C-FOKM



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.437 / Virus Database: 271.1.1/2917 - Release Date: 06/04/10
06:25:00




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



--
Garry Wright

Skepticism is the highest duty and blind faith the one unpardonable sin.
-- Thomas Huxley, (attributed: source unknown)




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------


--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.437 / Virus Database: 271.1.1/2918 - Release Date: 06/04/10
18:25:00




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] carburator bits

Posted: Sun Feb 19, 2012 6:23 pm
by Garry Wright
Thanks Si. Thats very helpful. This is not a normally replaced part and
does not appear in any of the lists I've found.

Garry

On 10-06-05 06:51 AM, Simon Smith wrote:
Gary,
The information came from my Precision Carburetors Manual. I don't know of a
source right now but you might try A.E.R.O. 1-800-362-3044 or El Reno
Aviation 405-262-2387.
Si
----- Original Message -----
From: "Garry Wright"<wright.garry30@gmail.com>
To:<rebel-builders@dcsol.com>
Sent: Saturday, June 05, 2010 6:39 AM
Subject: Re: [rebel-builders] carburator bits


Thanks Si. That could help a lot. Where did you find that and who is a
good supplier?

Garry

On 10-06-04 06:40 PM, Simon Smith wrote:
Gary,
The part # for the MA4SPA 10-3678-12 Mixture control metering valve assy.
is
242-514 hope this helps.
Si
----- Original Message -----
From: "Garry Wright"<wright.garry30@gmail.com>
To:<rebel-builders@dcsol.com>
Sent: Friday, June 04, 2010 11:39 AM
Subject: [rebel-builders] carburator bits



--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.437 / Virus Database: 271.1.1/2917 - Release Date: 06/04/10
06:25:00




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------




--
Garry Wright

Skepticism is the highest duty and blind faith the one unpardonable sin.
-- Thomas Huxley, (attributed: source unknown)




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.437 / Virus Database: 271.1.1/2918 - Release Date: 06/04/10
18:25:00




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



--
Garry Wright

Skepticism is the highest duty and blind faith the one unpardonable sin.
-- Thomas Huxley, (attributed: source unknown)




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[rebel-builders] carburator bits

Posted: Sun Feb 19, 2012 6:23 pm
by Garry Wright
I take that back. ACS has it for $79.85 but no info on it at all so I
was initially unable to find it.

G

On 10-06-05 06:51 AM, Simon Smith wrote:
Gary,
The information came from my Precision Carburetors Manual. I don't know of a
source right now but you might try A.E.R.O. 1-800-362-3044 or El Reno
Aviation 405-262-2387.
Si
----- Original Message -----
From: "Garry Wright"<wright.garry30@gmail.com>
To:<rebel-builders@dcsol.com>
Sent: Saturday, June 05, 2010 6:39 AM
Subject: Re: [rebel-builders] carburator bits


Thanks Si. That could help a lot. Where did you find that and who is a
good supplier?

Garry

On 10-06-04 06:40 PM, Simon Smith wrote:
Gary,
The part # for the MA4SPA 10-3678-12 Mixture control metering valve assy.
is
242-514 hope this helps.
Si
----- Original Message -----
From: "Garry Wright"<wright.garry30@gmail.com>
To:<rebel-builders@dcsol.com>
Sent: Friday, June 04, 2010 11:39 AM
Subject: [rebel-builders] carburator bits



--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.437 / Virus Database: 271.1.1/2917 - Release Date: 06/04/10
06:25:00




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------




--
Garry Wright

Skepticism is the highest duty and blind faith the one unpardonable sin.
-- Thomas Huxley, (attributed: source unknown)




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.437 / Virus Database: 271.1.1/2918 - Release Date: 06/04/10
18:25:00




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



--
Garry Wright

Skepticism is the highest duty and blind faith the one unpardonable sin.
-- Thomas Huxley, (attributed: source unknown)




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
All times are UTC-08:00
Page 1 of 1
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/