The Murphy Builders Site

Sounds like a "great" batch of "Rivets Unlimited's" rivets! Set them aside
and only use them for interior channels and such. Order a new box from
Mattic Industries.

MAM exchanged them at one point in time....

----- Original Message -----
From: "kevin curtis" <kcs1911@yahoo.com>
To: <rebel-builders@dcsol.com>
Sent: Sunday, May 09, 2010 10:40 PM
Subject: [rebel-builders] rivet mandrels

I have been doing a little work on my kit. I have found that about half of
the rivets leave a little sharp edge of the mandrel sticking out. Is this
common, or if not what can I do to stop it? Should I try turning the air
down so it pulls slower? or up to really pull them fast?
Kevin
623R






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

I had this problem with countersunk rivets until I started taking extra
special care to keep the rivet gun very square to the material. It was too
easy to lose focus on that. You're probably already on top of that but it
might be worth a try.

Ron


On Sun, May 9, 2010 at 7:40 PM, kevin curtis <kcs1911@yahoo.com> wrote:

I have been doing a little work on my kit. I have found that about half of
the rivets leave a little sharp edge of the mandrel sticking out. Is this
common, or if not what can I do to stop it? Should I try turning the air
down so it pulls slower? or up to really pull them fast?
Kevin
623R

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Yep, What Wayne said. I got

Do any of you know of any super rebel that successfully used the nose gear
package. I have been told that they did not perform well as say a 182 etc.
Luther Johnson

On Sun, May 9, 2010 at 10:40 PM, kevin curtis <kcs1911@yahoo.com> wrote:

I have been doing a little work on my kit. I have found that about half of
the rivets leave a little sharp edge of the mandrel sticking out. Is this
common, or if not what can I do to stop it? Should I try turning the air
down so it pulls slower? or up to really pull them fast?
Kevin
623R






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Hi, Kevin,
To correct this situation I use a smaller rivet nose diameter and redrill it
to a more appropriate size than with a dremel 1/4"diameter ball cutter and
machine a cupform on it.
I hope it help.
Daniel

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Luther
Johnson
Sent: 10 mai 2010 08:57
To: rebel-builders@dcsol.com
Subject: Re: [rebel-builders] rivet mandrels

Do any of you know of any super rebel that successfully used the nose gear
package. I have been told that they did not perform well as say a 182 etc.
Luther Johnson

On Sun, May 9, 2010 at 10:40 PM, kevin curtis <kcs1911@yahoo.com> wrote:

I have been doing a little work on my kit. I have found that about half of
the rivets leave a little sharp edge of the mandrel sticking out. Is this
common, or if not what can I do to stop it? Should I try turning the air
down so it pulls slower? or up to really pull them fast?
Kevin
623R






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------