The Murphy Builders Site

1/8th inch thick... yes that's the angle material to cut your TS-3 that the
stab struts attach to.

Hope they made it long enough... I've found in many kits that it was cut a
bit toooo short!

----- Original Message -----
From: "David Jackson" <canadjn@hotmail.com>
To: "Rebel Builders" <rebel-builders@dcsol.com>
Sent: Monday, March 22, 2010 11:02 PM
Subject: [rebel-builders] TS-3 Material and size

I can't find a part labelled TS-3. Can anyone tell me the size? I have
some pieces of 6 in long angle 1 1/2 in x 1 1/2, not sure of the thickness
(forgot to measure).



Dave Jackson

_________________________________________________________________
Live connected with Messenger on your phone
http://go.microsoft.com/?linkid=9712958



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

My TS-3 angle is only 1" per side, 1/8" thick, and total length is 5-7/8".

Ron


On Mon, Mar 22, 2010 at 8:10 PM, Wayne G. O'Shea <oifa@irishfield.on.ca>wrote:

1/8th inch thick... yes that's the angle material to cut your TS-3 that the
stab struts attach to.

Hope they made it long enough... I've found in many kits that it was cut a
bit toooo short!

----- Original Message -----
From: "David Jackson" <canadjn@hotmail.com>
To: "Rebel Builders" <rebel-builders@dcsol.com>
Sent: Monday, March 22, 2010 11:02 PM
Subject: [rebel-builders] TS-3 Material and size

I can't find a part labelled TS-3. Can anyone tell me the size? I have
some pieces of 6 in long angle 1 1/2 in x 1 1/2, not sure of the

thickness

(forgot to measure).

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

You are correct Ron! 1" x 1".. not 1.5 x 1.5 But if he has some 1.5 x 1.5
he can trim to suit...

----- Original Message -----
From: "Ron Shannon" <rshannon@cruzcom.com>
To: <rebel-builders@dcsol.com>
Sent: Tuesday, March 23, 2010 12:04 AM
Subject: Re: [rebel-builders] TS-3 Material and size

My TS-3 angle is only 1" per side, 1/8" thick, and total length is 5-7/8".

Ron


On Mon, Mar 22, 2010 at 8:10 PM, Wayne G. O'Shea
<oifa@irishfield.on.ca>wrote:

1/8th inch thick... yes that's the angle material to cut your TS-3 that
the
stab struts attach to.

Hope they made it long enough... I've found in many kits that it was cut
a
bit toooo short!

----- Original Message -----
From: "David Jackson" <canadjn@hotmail.com>
To: "Rebel Builders" <rebel-builders@dcsol.com>
Sent: Monday, March 22, 2010 11:02 PM
Subject: [rebel-builders] TS-3 Material and size

I can't find a part labelled TS-3. Can anyone tell me the size? I
have
some pieces of 6 in long angle 1 1/2 in x 1 1/2, not sure of the

thickness

(forgot to measure).

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

I have three pieces of 6 in by 1.5 x 1.5. Is there another area where this is required? (Or am I allowed a couple of "oopsies"?).



Dave J

From: oifa@irishfield.on.ca
To: rebel-builders@dcsol.com
Subject: Re: [rebel-builders] TS-3 Material and size
Date: Tue, 23 Mar 2010 09:20:29 -0400

You are correct Ron! 1" x 1".. not 1.5 x 1.5 But if he has some 1.5 x 1.5
he can trim to suit...

----- Original Message -----
From: "Ron Shannon" <rshannon@cruzcom.com>
To: <rebel-builders@dcsol.com>
Sent: Tuesday, March 23, 2010 12:04 AM
Subject: Re: [rebel-builders] TS-3 Material and size

My TS-3 angle is only 1" per side, 1/8" thick, and total length is 5-7/8".

Ron


On Mon, Mar 22, 2010 at 8:10 PM, Wayne G. O'Shea
<oifa@irishfield.on.ca>wrote:

1/8th inch thick... yes that's the angle material to cut your TS-3 that
the
stab struts attach to.

Hope they made it long enough... I've found in many kits that it was cut
a
bit toooo short!

----- Original Message -----
From: "David Jackson" <canadjn@hotmail.com>
To: "Rebel Builders" <rebel-builders@dcsol.com>
Sent: Monday, March 22, 2010 11:02 PM
Subject: [rebel-builders] TS-3 Material and size

thickness

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

_________________________________________________________________
IM on the go with Messenger on your phone
http://go.microsoft.com/?linkid=9712960



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------