The Murphy Builders Site

From: Wayne G. O'Shea <oifa@irishfield.on.ca>
Subject: [rebel-builders] Moose near calgary?
To: "Murphy Rebel Builders List" <rebel-builders@dcsol.com>
Date: Saturday, March 13, 2010, 4:55 PM
Might work better over here...

----- Original Message -----
From: "Michael Bleau " <bleaumichael@hotmail.com>
To: "Wayne G. O'Shea " <oifa@irishfield.on.ca>
Sent: Saturday, March 13, 2010 7:19 PM
Subject: Re: moose near calgary?

Does any have or know of a moose close to calgary that

has a murphy cowl

finished on it? We have fitted the cowl but need

figure how to bracket it

to the firewall and it would be a great help to see

one done. If anyone

has any suggestions as always they would be

appreciated. Thanks mike bleau

Sent on the TELUS Mobility network with BlackBerry

-----Original Message-----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
Date: Sat, 13 Mar 2010 17:32:49
To: <rebel-builders@dcsol.com>
Subject: Re: [rebel-builders] Worktable height

No issues for me on my 31" high table.... other than

it's too low to stand

beside and debur stuff on. Gets hard on the back if

you don't pull up a

chair to sit on. My 37" high table on the other hand

is perfect for

standing
up while deburing.

As for step stool being needed... buy an 8' long 2 x

12 and put it on two

cement blocks beside the table. Makes life a lot

easier when you're at a

stage that requires that extra boost!

----- Original Message -----
From: "Roland Kriening" <kriening@rogers.com>
To: <rebel-builders@dcsol.com>
Sent: Saturday, March 13, 2010 9:42 AM
Subject: [rebel-builders] Worktable height

I am halfway through completing the tailcone and

am finding I need a

stepstool to reach into the cone to drill and

rivet. My table is

currently
waist height. I am considering lowering the table

to a more workable

height
but don't want to do it too soon. I'm sure many

of you have gone there

done
that, so I await your advice. Is there an optimum

height for working on

the
fuselage? At what point in the build process

should I drop the table?

Roland
R56

-----------------------------------------------------------------

List archives located at: https://mail.dcsol.com/login
<https://mail.dcsol.com/login>
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com

Does any have or know of a moose close to calgary that has a murphy cowl
finished on it? We have fitted the cowl but need figure how to bracket it
to the firewall and it would be a great help to see one done. If anyone
has any suggestions as always they would be appreciated. Thanks mike bleau
Sent on the TELUS Mobility network with BlackBerry

-----Original Message-----
From: "Wayne G. O'Shea" <oifa@irishfield.on.ca>
Date: Sat, 13 Mar 2010 17:32:49
To: <rebel-builders@dcsol.com>
Subject: Re: [rebel-builders] Worktable height

No issues for me on my 31" high table.... other than it's too low to stand
beside and debur stuff on. Gets hard on the back if you don't pull up a
chair to sit on. My 37" high table on the other hand is perfect for
standing
up while deburing.

As for step stool being needed... buy an 8' long 2 x 12 and put it on two
cement blocks beside the table. Makes life a lot easier when you're at a
stage that requires that extra boost!

----- Original Message -----
From: "Roland Kriening" <kriening@rogers.com>
To: <rebel-builders@dcsol.com>
Sent: Saturday, March 13, 2010 9:42 AM
Subject: [rebel-builders] Worktable height

I am halfway through completing the tailcone and am finding I need a
stepstool to reach into the cone to drill and rivet. My table is
currently
waist height. I am considering lowering the table to a more workable
height
but don't want to do it too soon. I'm sure many of you have gone there
done
that, so I await your advice. Is there an optimum height for working on
the
fuselage? At what point in the build process should I drop the table?

Roland
R56






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
<https://mail.dcsol.com/login>
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
<https://mail.dcsol.com/login>
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------