The Murphy Builders Site

Posted: **Sun Feb 19, 2012 5:58 pm**

Hi Jesse!

This excerpt is right out of my CD manual in the 0320 eng install chapter:

0320 LYCOMING ENGINE INSTALLATION 29/04/98

34 - 6

7) Support the engine however you like as long as it will move without the
chance of dropping

it. Attach the engine mount to the engine with four Lord Mounts (94150-40),
four AN7-35A

bolts, eight AN970-716 washers and four AN363-720 locknuts.

It then follows with a "spiffy" full color diagram supporting the statement.
But as Ron says, don't forget the F.R.R.B! Craig

----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: "Builders list" <rebel-builders@dcsol.com>
Sent: Wednesday, January 20, 2010 1:38 PM
Subject: [rebel-builders] Lord mount bolt length

I have an o320 dynafocal mount and came up with J7402-24 for the part
number from Lord. Can anyone tell me what size (length and dia.) bolt to
order with these? Thanks.
Jesse

_________________________________________________________________
Hotmail: Trusted email with Microsoft's powerful SPAM protection.
http://clk.atdmt.com/GBL/go/196390706/direct/01/

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sun Feb 19, 2012 5:58 pm**

Thanks Craig,
These days I refer to the manual so infrequently that I sometimes forget it even exists. In this case I want to use genuine Lord mounts because they are supposedly better, offer more dampening etc. I believe the part # from the manual is actually a Barry part # even though MAM says Lord. I called Lord and was given the J7402-24 part # to fit the dynafocal mount with 1 3/8" diameter holes. I suppose that if I can't come up with the bolt to match these mounts then the one you quote from MAM would at least be a place to start.
Jesse

From: snowyrvr@mtaonline.net
To: rebel-builders@dcsol.com
Subject: Re: [rebel-builders] Lord mount bolt length
Date: Wed, 20 Jan 2010 18:30:44 -0900

Hi Jesse!

This excerpt is right out of my CD manual in the 0320 eng install chapter:

0320 LYCOMING ENGINE INSTALLATION 29/04/98

34 - 6

7) Support the engine however you like as long as it will move without the
chance of dropping

it. Attach the engine mount to the engine with four Lord Mounts (94150-40),
four AN7-35A

bolts, eight AN970-716 washers and four AN363-720 locknuts.

It then follows with a "spiffy" full color diagram supporting the statement.
But as Ron says, don't forget the F.R.R.B! Craig

----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: "Builders list" <rebel-builders@dcsol.com>
Sent: Wednesday, January 20, 2010 1:38 PM
Subject: [rebel-builders] Lord mount bolt length

I have an o320 dynafocal mount and came up with J7402-24 for the part
number from Lord. Can anyone tell me what size (length and dia.) bolt to
order with these? Thanks.
Jesse

_________________________________________________________________
Hotmail: Trusted email with Microsoft's powerful SPAM protection.
http://clk.atdmt.com/GBL/go/196390706/direct/01/

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

_________________________________________________________________
Your E-mail and More On-the-Go. Get Windows Live Hotmail Free.
http://clk.atdmt.com/GBL/go/196390709/direct/01/

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sun Feb 19, 2012 5:58 pm**

Are you using the CD instead of the manual? I need to get my butt back in gear one of these days and get back to work on my Rebel. I

Posted: **Sun Feb 19, 2012 5:58 pm**

Keith,
The cd Craig referred to is just the regular manual on cd from Murphy. My remark was a bit of ironic criticism on it. You were dreaming :-)
Jesse

Date: Thu, 21 Jan 2010 04:00:20 -0800
From: im_planecrazy@yahoo.com
Subject: RE: [rebel-builders] Lord mount bolt length
To: rebel-builders@dcsol.com

Are you using the CD instead of the manual? I need to get my butt back in gear one of these days and get back to work on my Rebel. I had thought I read that Wayne was going to produce a CD for a Rebel build as he did for the floats. But never read anything more about it. Maybe I am mistaken. He has fixed/built enough of them I am sure his tips and upgrades would be included and might make the build process less of a head scratching affair for us first time builders. But then maybe it was all a dream.;0

Keith R661

--- On Wed, 1/20/10, Jesse Jenks <jessejenks@hotmail.com> wrote:

From: Jesse Jenks <jessejenks@hotmail.com>
Subject: RE: [rebel-builders] Lord mount bolt length
To: "Builders list" <rebel-builders@dcsol.com>
Date: Wednesday, January 20, 2010, 10:15 PM

Thanks Craig,
These days I refer to the manual so infrequently that I sometimes forget it even exists. In this case I want to use genuine Lord mounts because they are supposedly better, offer more dampening etc. I believe the part # from the manual is actually a Barry part # even though MAM says Lord. I called Lord and was given the J7402-24 part # to fit the dynafocal mount with 1 3/8" diameter holes. I suppose that if I can't come up with the bolt to match these mounts then the one you quote from MAM would at least be a place to start.
Jesse

From: snowyrvr@mtaonline.net
To: rebel-builders@dcsol.com
Subject: Re: [rebel-builders] Lord mount bolt length
Date: Wed, 20 Jan 2010 18:30:44 -0900

Hi Jesse!

This excerpt is right out of my CD manual in the 0320 eng install chapter:

0320 LYCOMING ENGINE INSTALLATION 29/04/98

34 - 6

7) Support the engine however you like as long as it will move without the
chance of dropping

it. Attach the engine mount to the engine with four Lord Mounts (94150-40),
four AN7-35A

bolts, eight AN970-716 washers and four AN363-720 locknuts.

It then follows with a "spiffy" full color diagram supporting the statement.
But as Ron says, don't forget the F.R.R.B! Craig

----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: "Builders list" <rebel-builders@dcsol.com>
Sent: Wednesday, January 20, 2010 1:38 PM
Subject: [rebel-builders] Lord mount bolt length

I have an o320 dynafocal mount and came up with J7402-24 for the part
number from Lord. Can anyone tell me what size (length and dia.) bolt to
order with these? Thanks.
Jesse

_________________________________________________________________
Hotmail: Trusted email with Microsoft's powerful SPAM protection.
http://clk.atdmt.com/GBL/go/196390706/direct/01/

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

_________________________________________________________________
Your E-mail and More On-the-Go. Get Windows Live Hotmail Free.
http://clk.atdmt.com/GBL/go/196390709/direct/01/

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

_________________________________________________________________
Hotmail: Trusted email with powerful SPAM protection.
http://clk.atdmt.com/GBL/go/196390707/direct/01/

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sun Feb 19, 2012 5:58 pm**

Why did you have to wake me up??? It was a good dream! LOL
Keith

--- On Thu, 1/21/10, Jesse Jenks <jessejenks@hotmail.com> wrote:

From: Jesse Jenks <jessejenks@hotmail.com>
Subject: RE: [rebel-builders] Lord mount bolt length
To: "Builders list" <rebel-builders@dcsol.com>
Date: Thursday, January 21, 2010, 12:27 PM

Keith,
The cd Craig referred to is just the regular manual on cd from Murphy. My remark was a bit of ironic criticism on it. You were dreaming :-)
Jesse

[quote]Date: Thu, 21 Jan 2010 04:00:20 -0800
From: im_planecrazy@yahoo.com
Subject: RE: [rebel-builders] Lord mount bolt length
To: rebel-builders@dcsol.com

Are you using the CD instead of the manual? I need to get my butt back in gear one of these days and get back to work on my Rebel. I had thought I read that Wayne was going to produce a CD for a Rebel build as he did for the floats. But never read anything more about it. Maybe I am mistaken. He has fixed/built enough of them I am sure his tips and upgrades would be included and might make the build process less of a head scratching affair for us first time builders.

Posted: **Sun Feb 19, 2012 5:58 pm**

Keith, if that question was directed to me...

I find myself back and forth between the two large notebooks that came with
the kit (Manual 1 and 2), the 1998 single book which is strangely the same
size as the two old ones but contains the whole manual, and the CD-ROM
version dated? Mostly I use the CD ROM since I printed it out in color and
put all the pages in plastic sleeves. I ordered the single manual which
came with the CD for $400. :(

Original Message:
-----------------
From: Keith Leitch im_planecrazy@yahoo.com
Date: Thu, 21 Jan 2010 04:00:20 -0800 (PST)
To: rebel-builders@dcsol.com
Subject: RE: [rebel-builders] Lord mount bolt length

Are you using the CD instead of the manual? I need to get my butt back in
gear one of these days and get back to work on my Rebel. I

Posted: **Sun Feb 19, 2012 5:58 pm**

Nah.. it wasn't a dream Keith.. I just lost the gumption to full fill it for
you...

----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: "Builders list" <rebel-builders@dcsol.com>
Sent: Thursday, January 21, 2010 1:27 PM
Subject: RE: [rebel-builders] Lord mount bolt length

Keith,
The cd Craig referred to is just the regular manual on cd from Murphy. My
remark was a bit of ironic criticism on it. You were dreaming :-)
Jesse

Date: Thu, 21 Jan 2010 04:00:20 -0800
From: im_planecrazy@yahoo.com
Subject: RE: [rebel-builders] Lord mount bolt length
To: rebel-builders@dcsol.com

Are you using the CD instead of the manual? I need to get my butt back in
gear one of these days and get back to work on my Rebel. I had thought I
read that Wayne was going to produce a CD for a Rebel build as he did for
the floats. But never read anything more about it. Maybe I am mistaken.
He has fixed/built enough of them I am sure his tips and upgrades would
be included and might make the build process less of a head scratching
affair for us first time builders. But then maybe it was all a dream.;0

Keith R661

--- On Wed, 1/20/10, Jesse Jenks <jessejenks@hotmail.com> wrote:

From: Jesse Jenks <jessejenks@hotmail.com>
Subject: RE: [rebel-builders] Lord mount bolt length
To: "Builders list" <rebel-builders@dcsol.com>
Date: Wednesday, January 20, 2010, 10:15 PM

Thanks Craig,
These days I refer to the manual so infrequently that I sometimes forget
it even exists. In this case I want to use genuine Lord mounts because
they are supposedly better, offer more dampening etc. I believe the part
# from the manual is actually a Barry part # even though MAM says Lord. I
called Lord and was given the J7402-24 part # to fit the dynafocal mount
with 1 3/8" diameter holes. I suppose that if I can't come up with the
bolt to match these mounts then the one you quote from MAM would at least
be a place to start.
Jesse

From: snowyrvr@mtaonline.net
To: rebel-builders@dcsol.com
Subject: Re: [rebel-builders] Lord mount bolt length
Date: Wed, 20 Jan 2010 18:30:44 -0900

Hi Jesse!

This excerpt is right out of my CD manual in the 0320 eng install
chapter:

0320 LYCOMING ENGINE INSTALLATION 29/04/98

34 - 6

7) Support the engine however you like as long as it will move without
the
chance of dropping

it. Attach the engine mount to the engine with four Lord Mounts
(94150-40),
four AN7-35A

bolts, eight AN970-716 washers and four AN363-720 locknuts.

It then follows with a "spiffy" full color diagram supporting the
statement.
But as Ron says, don't forget the F.R.R.B! Craig

----- Original Message -----
From: "Jesse Jenks" <jessejenks@hotmail.com>
To: "Builders list" <rebel-builders@dcsol.com>
Sent: Wednesday, January 20, 2010 1:38 PM
Subject: [rebel-builders] Lord mount bolt length

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

_________________________________________________________________
Your E-mail and More On-the-Go. Get Windows Live Hotmail Free.
http://clk.atdmt.com/GBL/go/196390709/direct/01/

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

_________________________________________________________________
Hotmail: Trusted email with powerful SPAM protection.
http://clk.atdmt.com/GBL/go/196390707/direct/01/

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sun Feb 19, 2012 5:58 pm**

Ahhhh....come on Wayne....just for me....please. ;)
I totally understand. As I get older the less and less and can do......but I am still great in my mind. LOL