The Murphy Builders Site

Mike,
Off the top of my head, check the springs to make sure they are pulling the flaps all the way back to neutral.

Darryl


________________________________
From: Mike Davis <mike.davis@dcsol.com>
To: rebel-builders@dcsol.com
Sent: Tue, December 29, 2009 3:39:37 PM
Subject: [rebel-builders] Moose flap system

Help. I have the flap system installed and working, however, I can pull
the flap handle on full ( 39 degrees) and its fine when I release to " 0
degrees I goes only to 10 degrees

If I set the turn buckle to get 0 degrees, full flaps only go to 29 degrees
.. It looks as though I'm 10 degrees off.

I'm sure there is a simple answer, I'm just too cold to figure it out.

Any help would be appreciated.

Kelly
Moose
kelly@tru-form.ca
Enjoy your day !




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Let us know if the "tighten the spring" suggestion works Kelly.

Ted

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]
Sent: Tuesday, December 29, 2009 1:40 PM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Moose flap system

Help. I have the flap system installed and working, however, I can pull
the flap handle on full ( 39 degrees) and its fine when I release to " 0
degrees I goes only to 10 degrees

If I set the turn buckle to get 0 degrees, full flaps only go to 29 degrees

. It looks as though I'm 10 degrees off.

I'm sure there is a simple answer, I'm just too cold to figure it out.

Any help would be appreciated.

Kelly
Moose
kelly@tru-form.ca
Enjoy your day !




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------







-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Hey Darryl, yes that was the first thing I checked. Upon further studying I think the spring may be too low on the cabin upright, I did move it down to incorporate a custom doubler for the seat belt shoulder strap. I am moving it up a few inches and will see how this works.

Keep you posted

Kelly
Moose
kelly@tru-form.ca
Enjoy your day !


-----Original Message-----
From: Darryl Conway <kyhelo@bellsouth.net>
Date: Tue, 29 Dec 2009 15:30:52
To: <rebel-builders@dcsol.com>
Subject: Re: [rebel-builders] Moose flap system

Mike,
Off the top of my head, check the springs to make sure they are pulling the flaps all the way back to neutral.

Darryl


________________________________
From: Mike Davis <mike.davis@dcsol.com>
To: rebel-builders@dcsol.com
Sent: Tue, December 29, 2009 3:39:37 PM
Subject: [rebel-builders] Moose flap system

Help. I have the flap system installed and working, however, I can pull
the flap handle on full ( 39 degrees) and its fine when I release to " 0
degrees I goes only to 10 degrees

If I set the turn buckle to get 0 degrees, full flaps only go to 29 degrees
.. It looks as though I'm 10 degrees off.

I'm sure there is a simple answer, I'm just too cold to figure it out.

Any help would be appreciated.

Kelly
Moose
kelly@tru-form.ca
Enjoy your day !




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------







-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

I hope that solves it for you. Simple and easy is best.
Darryl




________________________________
From: Kelly M. Ewing <kelly@tru-form.ca>
To: MAM email list <rebel-builders@dcsol.com>
Sent: Wed, December 30, 2009 9:22:32 AM
Subject: Re: [rebel-builders] Moose flap system

Hey Darryl, yes that was the first thing I checked. Upon further studying I think the spring may be too low on the cabin upright, I did move it down to incorporate a custom doubler for the seat belt shoulder strap. I am moving it up a few inches and will see how this works.

Keep you posted

Kelly
Moose
kelly@tru-form.ca
Enjoy your day !


-----Original Message-----
From: Darryl Conway <kyhelo@bellsouth.net>
Date: Tue, 29 Dec 2009 15:30:52
To: <rebel-builders@dcsol.com>
Subject: Re: [rebel-builders] Moose flap system

Mike,
Off the top of my head, check the springs to make sure they are pulling the flaps all the way back to neutral.

Darryl


________________________________
From: Mike Davis <mike.davis@dcsol.com>
To: rebel-builders@dcsol.com
Sent: Tue, December 29, 2009 3:39:37 PM
Subject: [rebel-builders] Moose flap system

Help. I have the flap system installed and working, however, I can pull
the flap handle on full ( 39 degrees) and its fine when I release to " 0
degrees I goes only to 10 degrees

If I set the turn buckle to get 0 degrees, full flaps only go to 29 degrees
... It looks as though I'm 10 degrees off.

I'm sure there is a simple answer, I'm just too cold to figure it out.

Any help would be appreciated.

Kelly
Moose
kelly@tru-form.ca
Enjoy your day !




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------







-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------