The Murphy Builders Site

Posted: **Sun Feb 19, 2012 5:46 pm**

These are the ones I use.

http://www.bosunsupplies.com/products2. ... duct=S0322

----- Original Message -----
From: "Ken" <klehman@albedo.net>
To: <rebel-builders@dcsol.com>
Sent: Thursday, November 12, 2009 12:25 PM
Subject: Re: [rebel-builders] Sealing Tank

Jones, Michael wrote:
Ken

If you did not use those rings, what did you use

Cheers

Mike jones
snip
I used a stainless
female marine eye on a grade 5 bolt.
Mike I believe I purchased them from Westcoast Marine. They screw on the
end of a bolt and take the place of a nut.

Ken

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sun Feb 19, 2012 5:46 pm**

Wayne, Those rings look good, what size should I buy for my Moose?
Thanks;
Larry Luckinbill
117 Moose

-----Original Message-----
From: Wayne G. O'Shea <oifa@irishfield.on.ca>
To: rebel-builders@dcsol.com
Sent: Thu, Nov 12, 2009 10:31 am
Subject: Re: [rebel-builders] Tie down ring

These are the ones I use.
http://www.bosunsupplies.com/products2. ... duct=S0322

---- Original Message -----
rom: "Ken" <klehman@albedo.net>
o: <rebel-builders@dcsol.com>
ent: Thursday, November 12, 2009 12:25 PM
ubject: Re: [rebel-builders] Sealing Tank

Jones, Michael wrote:

Ken

If you did not use those rings, what did you use

Cheers

Mike jones
snip
I used a stainless
female marine eye on a grade 5 bolt.

Mike I believe I purchased them from Westcoast Marine. They screw on the
end of a bolt and take the place of a nut.

Ken

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sun Feb 19, 2012 5:46 pm**

Hi Larry,

Since the strut fittings are secured with AN4 bolts (1/4") then I would
recommend part # S0322-0007. If you like to use the next size larger, part
# S0322-0008 (5/16"), this can be done simply by increasing the hole
diameter where you are going to install the tie down ring. Up sizing bolt
hole from 1/4" to 5/16" is a non-issue.

Cheers,
Jeff

On Thu, Nov 12, 2009 at 12:44 PM, <skytrucks@aol.com> wrote:

Wayne, Those rings look good, what size should I buy for my Moose?
Thanks;
Larry Luckinbill
117 Moose

-----Original Message-----
From: Wayne G. O'Shea <oifa@irishfield.on.ca>
To: rebel-builders@dcsol.com
Sent: Thu, Nov 12, 2009 10:31 am
Subject: Re: [rebel-builders] Tie down ring

These are the ones I use.
http://www.bosunsupplies.com/products2. ... duct=S0322

---- Original Message -----
rom: "Ken" <klehman@albedo.net>
o: <rebel-builders@dcsol.com>
ent: Thursday, November 12, 2009 12:25 PM
ubject: Re: [rebel-builders] Sealing Tank

Jones, Michael wrote:
Ken

If you did not use those rings, what did you use

Cheers

Mike jones
snip
I used a stainless
female marine eye on a grade 5 bolt.
Mike I believe I purchased them from Westcoast Marine. They screw on the
end of a bolt and take the place of a nut.

Ken

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Posted: **Sun Feb 19, 2012 5:46 pm**

Also notice the 1/4 and 5/16 eyes are the same dimensions except for
the threaded hole. I bet you could re-tap the 1/4" one to 5/16 NF and
use a real AN bolt.
Joel

On Thu, Nov 12, 2009 at 4:33 PM, Jeff Micheal
<westcoastkitplanes@gmail.com> wrote:
[quote]Hi Larry,

Since the strut fittings are secured with AN4 bolts (1/4") then I would
recommend part # S0322-0007.