The Murphy Builders Site

what was the ??

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
hank@dcsol.com
Sent: Wednesday, October 07, 2009 9:00 PM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] VGs on the Rebel


The recommended location for VGs is at 10% cord. This location on the
Rebel is right about where the third row of rivets are located. Are the VGs
being placed forward or aft of this third row of rivets?

Hank

307R



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

The question is should the VGs be placed in front of or behind the third row
of rivets? Since the 10% of cord distance is a general rule of thumb, I'd
like to know what the placement on actual Rebels has been to give the best
performance.

Hank

On Wed, Oct 7, 2009 at 10:31 PM, Keith Oliver <kboliver47@roadrunner.com>wrote:

what was the ??

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
hank@dcsol.com
Sent: Wednesday, October 07, 2009 9:00 PM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] VGs on the Rebel


The recommended location for VGs is at 10% cord. This location on the
Rebel is right about where the third row of rivets are located. Are the
VGs
being placed forward or aft of this third row of rivets?

Hank

307R



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

Hank, I have the VG's on mine and installed them right at the 10% chord.
Can't remember exactly which row of rivets they were behind. But if you take
a square and make it flush with the leading edge and measure back 6 inches
(full chord is 60 inches), that is the location. The centre of the VG should
be 6 inches behind the leading edge. There was no interference with any
rivets on mine. They were spaced 3 inches apart.

I did mine exactly to the instructions given, and they worked out perfectly.

Walter

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Hank &
Vickie Balch
Sent: October 8, 2009 5:17 AM
To: rebel-builders@dcsol.com
Subject: Re: [rebel-builders] VGs on the Rebel

The question is should the VGs be placed in front of or behind the third row
of rivets? Since the 10% of cord distance is a general rule of thumb, I'd
like to know what the placement on actual Rebels has been to give the best
performance.

Hank

On Wed, Oct 7, 2009 at 10:31 PM, Keith Oliver
<kboliver47@roadrunner.com>wrote:

what was the ??

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com]On Behalf Of
hank@dcsol.com
Sent: Wednesday, October 07, 2009 9:00 PM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] VGs on the Rebel


The recommended location for VGs is at 10% cord. This location on the
Rebel is right about where the third row of rivets are located. Are the
VGs
being placed forward or aft of this third row of rivets?

Hank

307R



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------