[rebel-builders] Moose project front spar attach size
Posted: Sun Feb 19, 2012 5:32 pm
I will for sure get advise, anyone have Darryl s email
Kelly
kelly@tru-form.ca
Enjoy your day !
-----Original Message-----
From: "Ted Waltman" <ted@vafm.org>
Date: Tue, 8 Sep 2009 13:28:38
To: <rebel-builders@dcsol.com>
Subject: RE: [rebel-builders] Moose project front spar attach size
I can't imagine why the MAM-built wings have a 3/4" front attach hole size,
other than perhaps a mistake at the factory? I'd start worrying (perhaps?)
about edge-distance on the fitting at the 3/4" point. That size
bolt/fitting in that location has a whole bunch of stress on it!
In most any other location I'd say a spacer is Ok. However, since I'm not
an engineer, when you're talking about the spar attach point I would
encourage you to either talk to Darryl directly or to get some engineering
advice from someone (????).
Ted
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Kelly
M. Ewing
Sent: Tuesday, September 08, 2009 1:17 PM
To: rebel-builders@dcsol.com
Subject: Re: [rebel-builders] Moose project front spar attach size
Hi Ted thanks for the reply, I wish I knew of the email list a year ago, I
just found out about it 1 month ago from Bob. Thanks Bob.
Anyway, I am looking at the mam built wings and the front attachment hole is
3/4". The matching hole on the fuselage is 5/8"?
I see in the mods chapter 3 it does say 5/8" ( your correct Ted) . I wonder
why the wings have 3/4" holes and if a spacer is acceptable.
Thanks for your input.
Kelly
kelly@tru-form.ca
Enjoy your day !
-----Original Message-----
From: "Ted Waltman" <ted@vafm.org>
Date: Tue, 8 Sep 2009 12:30:57
To: <rebel-builders@dcsol.com>
Subject: RE: [rebel-builders] Moose project front spar attach size
3500 Modifications, Chap 3 says 5/8" Kelly. That's the size bolt on two
Moose that I just checked in my hangar too.
Where in the manual did you see the reference to 3/4"? I see an instance
where the advice used to be to go to a 1/2" hole, but I can't find any
reference to 3/4".
Ted Waltman
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Kelly
M. Ewing
Sent: Tuesday, September 08, 2009 10:21 AM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Moose project
New post, first question to rebel builders.
Does anyone know if the forward attachment brackets for the wings are to be
reamed out to 3/4" as stated in the manual? Because we are told to use an "
AN10 bolt ? This is 5/8. Perhaps we are to use a bushing? If so I've
missed this in the instructions.
Thanks in advance
Kelly
kelly@tru-form.ca
Enjoy your day !
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
Kelly
kelly@tru-form.ca
Enjoy your day !
-----Original Message-----
From: "Ted Waltman" <ted@vafm.org>
Date: Tue, 8 Sep 2009 13:28:38
To: <rebel-builders@dcsol.com>
Subject: RE: [rebel-builders] Moose project front spar attach size
I can't imagine why the MAM-built wings have a 3/4" front attach hole size,
other than perhaps a mistake at the factory? I'd start worrying (perhaps?)
about edge-distance on the fitting at the 3/4" point. That size
bolt/fitting in that location has a whole bunch of stress on it!
In most any other location I'd say a spacer is Ok. However, since I'm not
an engineer, when you're talking about the spar attach point I would
encourage you to either talk to Darryl directly or to get some engineering
advice from someone (????).
Ted
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Kelly
M. Ewing
Sent: Tuesday, September 08, 2009 1:17 PM
To: rebel-builders@dcsol.com
Subject: Re: [rebel-builders] Moose project front spar attach size
Hi Ted thanks for the reply, I wish I knew of the email list a year ago, I
just found out about it 1 month ago from Bob. Thanks Bob.
Anyway, I am looking at the mam built wings and the front attachment hole is
3/4". The matching hole on the fuselage is 5/8"?
I see in the mods chapter 3 it does say 5/8" ( your correct Ted) . I wonder
why the wings have 3/4" holes and if a spacer is acceptable.
Thanks for your input.
Kelly
kelly@tru-form.ca
Enjoy your day !
-----Original Message-----
From: "Ted Waltman" <ted@vafm.org>
Date: Tue, 8 Sep 2009 12:30:57
To: <rebel-builders@dcsol.com>
Subject: RE: [rebel-builders] Moose project front spar attach size
3500 Modifications, Chap 3 says 5/8" Kelly. That's the size bolt on two
Moose that I just checked in my hangar too.
Where in the manual did you see the reference to 3/4"? I see an instance
where the advice used to be to go to a 1/2" hole, but I can't find any
reference to 3/4".
Ted Waltman
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Kelly
M. Ewing
Sent: Tuesday, September 08, 2009 10:21 AM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Moose project
New post, first question to rebel builders.
Does anyone know if the forward attachment brackets for the wings are to be
reamed out to 3/4" as stated in the manual? Because we are told to use an "
AN10 bolt ? This is 5/8. Perhaps we are to use a bushing? If so I've
missed this in the instructions.
Thanks in advance
Kelly
kelly@tru-form.ca
Enjoy your day !
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------