tail handles

[Jones, Mike]

For those people looking for tail pull handles I found another source on the
web. Link is as follows

http://www.basinc-aeromod.com/


It is made for cessnas but all you need is fuselage dimension and they can
fit you with the right part, pice is 140 - 190 usd.

Also for Bob I would like gordons number for the bushing he makes, thanks
very much

Mike#007


EOM

NOTICE - This message is the property of HATCH. It may also be confidential
and/or privileged. If you are not the intended recipient of this message
you are hereby notified that you must not disseminate, copy or take any
action with respect to it. If you have received this message in error
please notify HATCH immediately via mailto:MailAdmin@hatch.ca.


*-----------------------------------------------------------------------------------*
The Murphy Rebel Builders List is for the discussion
between builders and owners of Murphy Rebel aircraft.
Archives located at:
http://www.dcsol.com/murphy-rebel/lists/default.htm
*-----------------------------------------------------------------------------------*




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Bob Patterson]

Sorry Mike - nobody has come back with Gordon Mohr's NEW phone
number or email address .... You might try to catch him at:
gmohr@telus.net

In any case, you would only need his bushing sets if you were
going to use Wayne's die-spring gear mod. (It REALLY <does> give a VERY
smooth ride !) (pass the BBQ sauce ;-) )

.....bobp

----------------------------orig.---------------------------------------
At 07:50 AM 10/6/00 -0400, you wrote:

For those people looking for tail pull handles I found another source on the
web. Link is as follows

http://www.basinc-aeromod.com/


It is made for cessnas but all you need is fuselage dimension and they can
fit you with the right part, pice is 140 - 190 usd.

Also for Bob I would like gordons number for the bushing he makes, thanks
very much

Mike#007


EOM

NOTICE - This message is the property of HATCH. It may also be confidential
and/or privileged. If you are not the intended recipient of this message
you are hereby notified that you must not disseminate, copy or take any
action with respect to it. If you have received this message in error
please notify HATCH immediately via mailto:MailAdmin@hatch.ca.


*--------------------------------------------------------------------------

---------*

The Murphy Rebel Builders List is for the discussion
between builders and owners of Murphy Rebel aircraft.
Archives located at:
http://www.dcsol.com/murphy-rebel/lists/default.htm
*--------------------------------------------------------------------------

---------*

*-----------------------------------------------------------------------------------*
The Murphy Rebel Builders List is for the discussion
between builders and owners of Murphy Rebel aircraft.
Archives located at:
http://www.dcsol.com/murphy-rebel/lists/default.htm
*-----------------------------------------------------------------------------------*




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Jims170A]

I have added 2 photos to the After Market Section.
One is of the tail handles on a Rebel and the other one is of some Spring
Gear mod's. I still have not been able to down load the changes to the Manual
for the Spring Gear yet.

Here is the contact info for the tail handles.

Keith Kinden 406-293-9026 Fax 406-293-9776 Email Keith@montanafloat.com
<A HREF="http://www.montanafloat.com/">Montana Float Co., Inc. Libby, Montana
</A>

A look at his web site will show his quality and capabilities. He makes
ground handles for the Rebel and SR as well as Amphib Floats for Rebel and
SR. Check out the photo of the Elite on Amphibs.
Call him for prices.
Jim LePard, Rebel 254



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[klehman]

I like the foot step in the side of his amphibs.
Ken

Jims170A@cs.com wrote:

snip
Keith Kinden 406-293-9026 Fax 406-293-9776 Email Keith@montanafloat.com
<A HREF="http://www.montanafloat.com/">Montana Float Co., Inc. Libby, Montana
</A>

A look at his web site will show his quality and capabilities. He makes
ground handles for the Rebel and SR as well as Amphib Floats for Rebel and
SR. Check out the photo of the Elite on Amphibs.
Call him for prices.

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------