TAIL CONE STRINGERS (BEEF-UP)

[kyle martin]

MOOSE BUILDERS,

FOR THOSE OF YOU WHO BEEFED UP THE TAIL CONE OF YOUR SR3500 USING THE 2"
U-CHANNEL MATERIAL, THAT IS INCORPORATED INTO MANY OTHER AREAS OF THE
AIRFRAME, AND RAN IT BETWEEN BULKHEADS:

I AM TRYING TO FIND THE MOST COST/TIME EFFECTIVE WAY TO MAKE, OR BUY 100'+
OF THIS TO INCORPORATE INTO A TAIL CONE BEEF-UP, SIMILAR TO HOW STEVE AND
MANY OTHERS DID IT; USING CORNER WRAPS AND ADDITIONAL STRINGERS IN FLOOR AND
ROOF - THAT GO BETWEEN BULKHEADS.

MAM WANTS WAY TOO MUCH PER FOOT FOR THEIR U CHANNEL MATERIAL, SO I NEED TO
FIGURE OUT ANOTHER WAY. ANY ADVICE IS APPRECIATED.

THANKS

KYLE
019SR

On Mon, Jan 26, 2009 at 4:59 PM, <bransom@dcsol.com> wrote:

I meant to say that MAM instructions are to drill the two additional holes.
Mine (496R) doesn't have the holes predrilled either, which just seems a
little odd since the rest of the holes are already there. Guess I'll just
go ahead and drill them for now.
-Ben

Hi Ben
Mine don't have those holes. May be it because mine is a later S/N 802R
Charlie
----- Original Message -----
From: <bransom@dcsol.com>
To: <rebel-builders@dcsol.com>
Sent: Monday, January 26, 2009 10:41 AM
Subject: [rebel-builders] rear spar attach bracket

Hi all,
MAM has a couple extra holes drilled in the rear spar attach bracket.

Are

these just extra rivet holes or are they for some other purpose?

Picture for reference:
http://mae.ucdavis.edu/ransom/Murphy/mi ... Attach.jpg

Thanks,
-Ben, 496R



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[bscheube]

kyle,

if you do not have a metal break, find a local metal fab shop and take a
piece of the 'u' channel in and some flat stock. they can cut and bend to
match i believe its 6061 t6 .032 that i made mine out of. the cost should
be low less than an hour shop labor time. just make sure the bender has a
softer radius than they use on the steel (to tight will crack). bob moose191



On 1/27/2009 2:09 PM, alpsnowman@gmail.com wrote to rebel-builders:

-> MOOSE BUILDERS,
->
-> FOR THOSE OF YOU WHO BEEFED UP THE TAIL CONE OF YOUR SR3500 USING THE 2"
-> U-CHANNEL MATERIAL, THAT IS INCORPORATED INTO MANY OTHER AREAS OF THE
-> AIRFRAME, AND RAN IT BETWEEN BULKHEADS:
->
-> I AM TRYING TO FIND THE MOST COST/TIME EFFECTIVE WAY TO MAKE, OR BUY 100'+
-> OF THIS TO INCORPORATE INTO A TAIL CONE BEEF-UP, SIMILAR TO HOW STEVE AND
-> MANY OTHERS DID IT; USING CORNER WRAPS AND ADDITIONAL STRINGERS IN FLOOR AND
-> ROOF - THAT GO BETWEEN BULKHEADS.
->
-> MAM WANTS WAY TOO MUCH PER FOOT FOR THEIR U CHANNEL MATERIAL, SO I NEED TO
-> FIGURE OUT ANOTHER WAY. ANY ADVICE IS APPRECIATED.
->
-> THANKS
->
-> KYLE
-> 019SR
->
-> On Mon, Jan 26, 2009 at 4:59 PM, <bransom@dcsol.com> wrote:
->
-> > I meant to say that MAM instructions are to drill the two additional
holes.
-> > Mine (496R) doesn't have the holes predrilled either, which just seems a
-> > little odd since the rest of the holes are already there. Guess I'll just
-> > go ahead and drill them for now.
-> > -Ben
-> >
-> > > Hi Ben
-> > > Mine don't have those holes. May be it because mine is a later S/N 802R
-> > > Charlie
-> > > ----- Original Message -----
-> > > From: <bransom@dcsol.com>
-> > > To: <rebel-builders@dcsol.com>
-> > > Sent: Monday, January 26, 2009 10:41 AM
-> > > Subject: [rebel-builders] rear spar attach bracket
-> > >
-> > >
-> > > > Hi all,
-> > > > MAM has a couple extra holes drilled in the rear spar attach bracket.
-> > Are
-> > > > these just extra rivet holes or are they for some other purpose?
-> > > >
-> > > > Picture for reference:
-> > > > http://mae.ucdavis.edu/ransom/Murphy/mi ... Attach.jpg
-> > > >
-> > > > Thanks,
-> > > > -Ben, 496R
-> > > >
-> > > >
-> > > >
-> > > > -----------------------------------------------------------------
-> > > > List archives located at: https://mail.dcsol.com/login
-> > > > username "rebel" password "builder"
-> > > > Unsubscribe: rebel-builders-unsubscribe@dcsol.com
-> > > > List administrator: mike.davis@dcsol.com
-> > > > -----------------------------------------------------------------
-> > > >
-> > > >
-> > > >
-> > > >
-> > > >
-> > >
-> >
-> >
-> >
-> >
-> > -----------------------------------------------------------------
-> > List archives located at: https://mail.dcsol.com/login
-> > username "rebel" password "builder"
-> > Unsubscribe: rebel-builders-unsubscribe@dcsol.com
-> > List administrator: mike.davis@dcsol.com
-> > -----------------------------------------------------------------
-> >
-> >
-> >
-> >
->




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[bscheube]

here are a couple other ideas for tail cone
https://mail.dcsol.com/file/area107/Bottom422.jpg
https://mail.dcsol.com/file/area107/H_StabMount_c.jpg
https://mail.dcsol.com/file/area107/AccessHoles.jpg
https://mail.dcsol.com/file/area107/DoublersLabeled.jpg
bob moose191

On 1/27/2009 2:09 PM, alpsnowman@gmail.com wrote to rebel-builders:

-> MOOSE BUILDERS,
->
-> FOR THOSE OF YOU WHO BEEFED UP THE TAIL CONE OF YOUR SR3500 USING THE 2"
-> U-CHANNEL MATERIAL, THAT IS INCORPORATED INTO MANY OTHER AREAS OF THE
-> AIRFRAME, AND RAN IT BETWEEN BULKHEADS:
->
-> I AM TRYING TO FIND THE MOST COST/TIME EFFECTIVE WAY TO MAKE, OR BUY 100'+
-> OF THIS TO INCORPORATE INTO A TAIL CONE BEEF-UP, SIMILAR TO HOW STEVE AND
-> MANY OTHERS DID IT; USING CORNER WRAPS AND ADDITIONAL STRINGERS IN FLOOR AND
-> ROOF - THAT GO BETWEEN BULKHEADS.
->
-> MAM WANTS WAY TOO MUCH PER FOOT FOR THEIR U CHANNEL MATERIAL, SO I NEED TO
-> FIGURE OUT ANOTHER WAY. ANY ADVICE IS APPRECIATED.
->
-> THANKS
->
-> KYLE
-> 019SR
->
-> On Mon, Jan 26, 2009 at 4:59 PM, <bransom@dcsol.com> wrote:
->
-> > I meant to say that MAM instructions are to drill the two additional
holes.
-> > Mine (496R) doesn't have the holes predrilled either, which just seems a
-> > little odd since the rest of the holes are already there. Guess I'll just
-> > go ahead and drill them for now.
-> > -Ben
-> >
-> > > Hi Ben
-> > > Mine don't have those holes. May be it because mine is a later S/N 802R
-> > > Charlie
-> > > ----- Original Message -----
-> > > From: <bransom@dcsol.com>
-> > > To: <rebel-builders@dcsol.com>
-> > > Sent: Monday, January 26, 2009 10:41 AM
-> > > Subject: [rebel-builders] rear spar attach bracket
-> > >
-> > >
-> > > > Hi all,
-> > > > MAM has a couple extra holes drilled in the rear spar attach bracket.
-> > Are
-> > > > these just extra rivet holes or are they for some other purpose?
-> > > >
-> > > > Picture for reference:
-> > > > http://mae.ucdavis.edu/ransom/Murphy/mi ... Attach.jpg
-> > > >
-> > > > Thanks,
-> > > > -Ben, 496R
-> > > >
-> > > >
-> > > >
-> > > > -----------------------------------------------------------------
-> > > > List archives located at: https://mail.dcsol.com/login
-> > > > username "rebel" password "builder"
-> > > > Unsubscribe: rebel-builders-unsubscribe@dcsol.com
-> > > > List administrator: mike.davis@dcsol.com
-> > > > -----------------------------------------------------------------
-> > > >
-> > > >
-> > > >
-> > > >
-> > > >
-> > >
-> >
-> >
-> >
-> >
-> > -----------------------------------------------------------------
-> > List archives located at: https://mail.dcsol.com/login
-> > username "rebel" password "builder"
-> > Unsubscribe: rebel-builders-unsubscribe@dcsol.com
-> > List administrator: mike.davis@dcsol.com
-> > -----------------------------------------------------------------
-> >
-> >
-> >
-> >
->




-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------