Hi Roger
Hope you're all keeping well in Chicago ?
When I did mine they did fit OK but I seem to remember only one way. It
looks square but it isn't so I didn't need to file it down at all when I
figured it out (although it seems a lifetime ago now it was only a couple of
years ago !!) :-)
Nig
745E
Still building :-)
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Roger
Cole
Sent: 12 December 2008 21:51
To: Rebel Builders
Subject: [rebel-builders] Parts do not fit
Instruction 9.23.9 says "Align the FUS-86 part inside the FUS-85
bracket, then mark and trim off the end of FUS-85 as shown." The
problem is that the FUS-86 is 1-inch thick, and the inside width of
FUS-85 is 15/16 inch. FUS-86 does not fit inside FUS-85. Should I
machine 1/32 inch off each side of the FUS-86?
Roger Cole
Murphy Elite #709
rcole927@earthlink.net
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
Do you want this big green box to go away? Well here's how...
Click here for full update
Wildcat! photo archives restored.
Click here for full update
Donors can now disable ads.
Click here for instructions
Add yourself to the user map.
Click here for instructions
Click here for full update
Wildcat! photo archives restored.
Click here for full update
Donors can now disable ads.
Click here for instructions
Add yourself to the user map.
Click here for instructions
[rebel-builders] Parts do not fit
[rebel-builders] Parts do not fit
Hi Nigel,
Things are good here, except for the interesting politics.
Were you able to get the diesel engine that you wanted?
All of my FUS-86s are 1-inch, square. All of my FUS-85s are 15/16-
inch inside width, so the FUS-86s don't fit inside the FUS-85s.
Roger Cole
Murphy Elite #709
rcole927@earthlink.net
On Dec 13, 2008, at 1:33 PM, N.Smith wrote:
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
Things are good here, except for the interesting politics.
Were you able to get the diesel engine that you wanted?
All of my FUS-86s are 1-inch, square. All of my FUS-85s are 15/16-
inch inside width, so the FUS-86s don't fit inside the FUS-85s.
Roger Cole
Murphy Elite #709
rcole927@earthlink.net
On Dec 13, 2008, at 1:33 PM, N.Smith wrote:
Hi Roger
Hope you're all keeping well in Chicago ?
When I did mine they did fit OK but I seem to remember only one
way. It
looks square but it isn't so I didn't need to file it down at all
when I
figured it out (although it seems a lifetime ago now it was only a
couple of
years ago !!) :-)
Nig
745E
Still building :-)
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf
Of Roger
Cole
Sent: 12 December 2008 21:51
To: Rebel Builders
Subject: [rebel-builders] Parts do not fit
Instruction 9.23.9 says "Align the FUS-86 part inside the FUS-85
bracket, then mark and trim off the end of FUS-85 as shown." The
problem is that the FUS-86 is 1-inch thick, and the inside width of
FUS-85 is 15/16 inch. FUS-86 does not fit inside FUS-85. Should I
machine 1/32 inch off each side of the FUS-86?
Roger Cole
Murphy Elite #709
rcole927@earthlink.net
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
[rebel-builders] Parts do not fit
Hi Roger
That's not a problem I had so I can't help I'm afraid. I'd be a bit cautious
about filing it down as it carries all the engine mount forces so suggest
you try an email to MAM and see what they recommend. It was a very flush fit
on mine but it did fit !
Still waiting and hoping for my diesel :-)
Nig
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Roger
Cole
Sent: 13 December 2008 22:53
To: rebel-builders@dcsol.com
Subject: Re: [rebel-builders] Parts do not fit
Hi Nigel,
Things are good here, except for the interesting politics.
Were you able to get the diesel engine that you wanted?
All of my FUS-86s are 1-inch, square. All of my FUS-85s are 15/16-
inch inside width, so the FUS-86s don't fit inside the FUS-85s.
Roger Cole
Murphy Elite #709
rcole927@earthlink.net
On Dec 13, 2008, at 1:33 PM, N.Smith wrote:
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
That's not a problem I had so I can't help I'm afraid. I'd be a bit cautious
about filing it down as it carries all the engine mount forces so suggest
you try an email to MAM and see what they recommend. It was a very flush fit
on mine but it did fit !
Still waiting and hoping for my diesel :-)
Nig
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Roger
Cole
Sent: 13 December 2008 22:53
To: rebel-builders@dcsol.com
Subject: Re: [rebel-builders] Parts do not fit
Hi Nigel,
Things are good here, except for the interesting politics.
Were you able to get the diesel engine that you wanted?
All of my FUS-86s are 1-inch, square. All of my FUS-85s are 15/16-
inch inside width, so the FUS-86s don't fit inside the FUS-85s.
Roger Cole
Murphy Elite #709
rcole927@earthlink.net
On Dec 13, 2008, at 1:33 PM, N.Smith wrote:
Hi Roger
Hope you're all keeping well in Chicago ?
When I did mine they did fit OK but I seem to remember only one
way. It
looks square but it isn't so I didn't need to file it down at all
when I
figured it out (although it seems a lifetime ago now it was only a
couple of
years ago !!) :-)
Nig
745E
Still building :-)
-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf
Of Roger
Cole
Sent: 12 December 2008 21:51
To: Rebel Builders
Subject: [rebel-builders] Parts do not fit
Instruction 9.23.9 says "Align the FUS-86 part inside the FUS-85
bracket, then mark and trim off the end of FUS-85 as shown." The
problem is that the FUS-86 is 1-inch thick, and the inside width of
FUS-85 is 15/16 inch. FUS-86 does not fit inside FUS-85. Should I
machine 1/32 inch off each side of the FUS-86?
Roger Cole
Murphy Elite #709
rcole927@earthlink.net
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------
-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------