[rebel-builders] Door sill install question

[Eric Fogelin]

I just took a look a look at my notes and photographs. I did drill #30 and
rivet the door sills but not in either the front or rear positions where you
will eventually rivet the door sills to the square tube cage and at the rear
to the vertical skins that attach the cabin to the tail. As I recall, these
still require some extra measuring and squaring before final drill and
rivet. Leave those #40 until you have to tops of the door and roof skin in
place. Even then, you have some other skins that go forward to the firewall
that still need to be fitted.

Eric Fogelin
Elite 645



-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Roger
Cole
Sent: Thursday, June 05, 2008 6:40 PM
To: Rebel Builders
Subject: [rebel-builders] Door sill install question

I have completed the instructions titled "Door Sill Install" which
says to drill the holes to #40 and cleco together. I couldn't find
an instruction to drill out to #30, deburr, chromate, and rivet. Is
there a later step that requires that the holes be left at #40, or
should I drill out to #30 and rivet now?

Thanks in advance for your helpful advice.


Roger Cole
Murphy Elite #709
rcole927@earthlink.net







-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Roger Cole]

Eric,
Thanks! That is exactly the information that I need.
---------------Roger
On Jun 5, 2008, at 11:47 PM, Eric Fogelin wrote:

I just took a look a look at my notes and photographs. I did drill
#30 and
rivet the door sills but not in either the front or rear positions
where you
will eventually rivet the door sills to the square tube cage and at
the rear
to the vertical skins that attach the cabin to the tail. As I
recall, these
still require some extra measuring and squaring before final drill and
rivet. Leave those #40 until you have to tops of the door and roof
skin in
place. Even then, you have some other skins that go forward to the
firewall
that still need to be fitted.

Eric Fogelin
Elite 645



-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf
Of Roger
Cole
Sent: Thursday, June 05, 2008 6:40 PM
To: Rebel Builders
Subject: [rebel-builders] Door sill install question

I have completed the instructions titled "Door Sill Install" which
says to drill the holes to #40 and cleco together. I couldn't find
an instruction to drill out to #30, deburr, chromate, and rivet. Is
there a later step that requires that the holes be left at #40, or
should I drill out to #30 and rivet now?

Thanks in advance for your helpful advice.


Roger Cole
Murphy Elite #709
rcole927@earthlink.net







-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------