[rebel-builders] trimming skins

[Wayne G. O'Shea]

Outboard end ...yes... in line with the end rib of the stab/fin.. inboard
end.. do not be in a rush to trim them. It can be nicely fitted to the
fuselage to need nothing but a rubber edging to fill the gap between the
two.

----- Original Message -----
From: "Rebecca Brownell" <brownell@candlelight.ca>
To: <rebel-builders@dcsol.com>
Sent: Wednesday, May 07, 2008 8:01 PM
Subject: [rebel-builders] trimming skins

Hi all
I wanted to double check something that wasn't overly clear in the
manual.
When trimming the leading edge skins on the fin and stabs,I am assuming
they ere trimmed flush and parallel to the ends.I apologise if this
seems like a stupid question.

Any words of wisdom appreciated.
thanks
Jason
817R



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Rebecca Brownell]

thanks Wayne
I was wondering that exact thing(fitting to the fuselage)very
helpful,thanks
Jason
On 7-May-08, at 8:03 PM, Wayne G. O'Shea wrote:

Outboard end ...yes... in line with the end rib of the stab/fin..
inboard
end.. do not be in a rush to trim them. It can be nicely fitted to the
fuselage to need nothing but a rubber edging to fill the gap
between the
two.

----- Original Message -----
From: "Rebecca Brownell" <brownell@candlelight.ca>
To: <rebel-builders@dcsol.com>
Sent: Wednesday, May 07, 2008 8:01 PM
Subject: [rebel-builders] trimming skins

Hi all
I wanted to double check something that wasn't overly clear in the
manual.
When trimming the leading edge skins on the fin and stabs,I am
assuming
they ere trimmed flush and parallel to the ends.I apologise if this
seems like a stupid question.

Any words of wisdom appreciated.
thanks
Jason
817R



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[snowyrvr@mtaonline.net]

Right! I just took a large rubber band and stretched it around even with
the rib edge. It's easy to move it until it's exactly even with the edge
and symetrical. Then use a marker and make your line.

Original Message:
-----------------
From: Rebecca Brownell brownell@candlelight.ca
Date: Wed, 7 May 2008 20:01:31 -0400
To: rebel-builders@dcsol.com
Subject: [rebel-builders] trimming skins


Hi all
I wanted to double check something that wasn't overly clear in the
manual.
When trimming the leading edge skins on the fin and stabs,I am assuming
they ere trimmed flush and parallel to the ends.I apologise if this
seems like a stupid question.

Any words of wisdom appreciated.
thanks
Jason
817R



-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------





--------------------------------------------------------------------
mail2web LIVE