[rebel-builders] Moose - New V-Brace design

[Mike Kimball]

Looks like a good design. I'm gonna wait until I actually develop damage to
mine before I go through the trouble of removing the windshield. Since the
V-brace is really only needed for float operations can I assume floats are
in your future?

Mike

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Ted
Waltman
Sent: Friday, March 30, 2007 8:13 PM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Moose - New V-Brace design

I just uploaded two pictures to S/M 107-Fuselage of a new FUS-0717, V-Brace,
design by Dale Fultz (thanks Dale!). I annotated the pictures with the
measurements of all the components. All are of 4130 except for the washer,
which is stainless. The design uses 3/8" bolts.

Ted Waltman





-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Rick Muller]

Mike,

When I discussed using a V8 in my plane with Murphy they recommended the V
brace. They suggested it because of the heavier engine. They indicate that
in their smaller planes when heavier engines were used they saw some damage
to the lower firewall on hard landings. The thought is that on the hard
landing the moment arm of the engine is such that it causes large
compression of the lower firewall attach points. The V brace distributes
the load in such situations to the upper part of the airframe. Just some
thoughts.

Rick Muller
(303) 664 9219 Home
(303) 641 6623 Cell
rickhm@comcast.net

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Mike
Kimball
Sent: Friday, March 30, 2007 10:07 PM
To: rebel-builders@dcsol.com
Subject: RE: [rebel-builders] Moose - New V-Brace design

Looks like a good design. I'm gonna wait until I actually develop damage to
mine before I go through the trouble of removing the windshield. Since the
V-brace is really only needed for float operations can I assume floats are
in your future?

Mike

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Ted
Waltman
Sent: Friday, March 30, 2007 8:13 PM
To: rebel-builders@dcsol.com
Subject: [rebel-builders] Moose - New V-Brace design

I just uploaded two pictures to S/M 107-Fuselage of a new FUS-0717, V-Brace,
design by Dale Fultz (thanks Dale!). I annotated the pictures with the
measurements of all the components. All are of 4130 except for the washer,
which is stainless. The design uses 3/8" bolts.

Ted Waltman





-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Fred Messinger (fredm)]

Hi All,

I notice a FUS-370 in some pictures recvently uploaded pictures - they
mainly pertained to the tail cone. Did this part come from MAM? I got my
moose in August and I don't even have that part on my inventory list.

Thanks,
Fred

On 3/31/07, Ted Waltman <tedwaltman@i1ci.com> wrote:

I just uploaded two pictures to S/M 107-Fuselage of a new FUS-0717,
V-Brace,
design by Dale Fultz (thanks Dale!). I annotated the pictures with the
measurements of all the components. All are of 4130 except for the
washer,
which is stainless. The design uses 3/8" bolts.

Ted Waltman





-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------