Inspection covers

[Alan Hepburn]

The inspection hole on the Montana floats is 5" diameter. The plate is 6.5"
diameter.

Al
----- Original Message -----
From: "Dale Fultz" <dfultz17086@earthlink.net>
To: <rebel-builders@dcsol.com>
Sent: Monday, March 14, 2005 11:09 PM
Subject: Re: Inspection covers

what size are they being made in (Diameter) would like to find 6 inch ones
to put in lower fuselage to check motor mount nuts and rudder pedals from
underneath. Thanks Dale
----- Original Message -----
From: "Mike Betti" <mbetti@up.net>
To: <rebel-builders@dcsol.com>
Sent: Monday, March 14, 2005 10:22 PM
Subject: Re: Inspection covers

Any ideas on the cost of these?

----- Original Message -----
From: "Dick Shotwell" <dicks@filertel.com>
To: "Moose Builders" <rebel-builders@dcsol.com>
Sent: Monday, March 14, 2005 9:15 PM
Subject: Inspection covers

Just a note to anyone who wants to install more easily removable
inspection covers. We wanted to be able to easily remove the

inspection

covers and we wanted them held in place with stainless steel screws
screwed into nut plates. We found that Keith Kinden at Montana Floats
can make these up. He fabricates a donut into which the nut plates

are

installed as well as a cover with matching screw holes. The donut is
placed in the structure (wing, stab, fuse, or wherever) with proseal.
Makes a nice clean installation.
Dick and Dave Shotwell
Moose 096
N235DS
Twin Falls, ID



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------





--
No virus found in this incoming message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.7.2 - Release Date: 3/11/05

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[Mike Betti]

Thanks for the tip.

----- Original Message -----
From: "Scott Aldrich" <sa@mwutah.com>
To: <rebel-builders@dcsol.com>
Sent: Monday, March 14, 2005 10:16 PM
Subject: RE: Inspection covers

Give Keith a call at Montana Floats (406) 293-9026. I think they can make
just about whatever you want. I recall ours were 5 or maybe 6 inch and

$12

for the ring and plate but that was a while ago.

Keith lurks on here but it is best to call him for fastest service.

Scott

-----Original Message-----
From: mike.davis@dcsol.com [mailto:mike.davis@dcsol.com] On Behalf Of Dale
Fultz
Sent: Monday, March 14, 2005 9:09 PM
To: rebel-builders@dcsol.com
Subject: Re: Inspection covers

what size are they being made in (Diameter) would like to find 6 inch ones
to put in lower fuselage to check motor mount nuts and rudder pedals from
underneath. Thanks Dale
----- Original Message -----
From: "Mike Betti" <mbetti@up.net>
To: <rebel-builders@dcsol.com>
Sent: Monday, March 14, 2005 10:22 PM
Subject: Re: Inspection covers

Any ideas on the cost of these?

----- Original Message -----
From: "Dick Shotwell" <dicks@filertel.com>
To: "Moose Builders" <rebel-builders@dcsol.com>
Sent: Monday, March 14, 2005 9:15 PM
Subject: Inspection covers

Just a note to anyone who wants to install more easily removable
inspection covers. We wanted to be able to easily remove the

inspection

covers and we wanted them held in place with stainless steel screws
screwed into nut plates. We found that Keith Kinden at Montana Floats
can make these up. He fabricates a donut into which the nut plates

are

installed as well as a cover with matching screw holes. The donut is
placed in the structure (wing, stab, fuse, or wherever) with proseal.
Makes a nice clean installation.
Dick and Dave Shotwell
Moose 096
N235DS
Twin Falls, ID



-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------





--
No virus found in this incoming message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.7.2 - Release Date: 3/11/05

-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------






-----------------------------------------------------------------
List archives located at: https://www.dcsol.com/login?mode=HTML
username "rebel" password "builder"
Subscription services located at:
https://www.dcsol.com/public/code/html-subscribe.htm
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------