[AVIS-NOTICE] Fw: flush avex rivet

[Jean Poirier]

I Jim
Do you have info about "Brown tool"?
Jean
Rebel 747R
----- Original Message -----
From: "goody" <goody@sover.net>
To: <murphy-rebel@dcsol.com>
Sent: Friday, December 05, 2003 10:58 AM
Subject: [AVIS-NOTICE] Fw: flush avex rivet

I have 120' countersinks with centering mandrels from Brown tool.
Jim
----- Original Message -----
From: <klehman@albedo.net>
To: <murphy-rebel@dcsol.com>
Sent: Thursday, December 04, 2003 12:43 PM
Subject: Re: flush avex rivet

Jean

120 degree countersinks are available in single flute and multi-flute
from tool suppliers but the ones that I have do not have a mandrel and
are not self centering. However a normal 118 degree drill bit will
finish the countersink a little better than just a 100 degree cutter and
help you get a flush surface after you rivet.

120 degrees seems to be common for non aviation blind rivets including
avex, pop, and the structural Q rivets.

Ken

Wayne G. O'Shea wrote:

The Avex RV44's are actually 118 to 120 degrees, but the 100 c/s is

pretty

close and I have to admit that I've cheated a >few< times!
Wayne

----- Original Message -----
From: "Jean Poirier" <oxyport@globetrotter.net>
To: <murphy-rebel@dcsol.com>
Sent: Thursday, December 04, 2003 11:07 AM
Subject: flush avex rivet


aileron. Murphy ask to contersink with a grind 1/2' drill but they do

not

specifid the rivets angle! I have use a microstop contersing cutter

for

solid rivet (100 deg.) It looks ok but is it? what is the degree for

those

Avex flush rivet?

*-------------------------------------------------------------------------*

To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*
*-------------------------------------------------------------------------*

To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*




*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------

[goody]

Brown Aviation Tool Supply Co.
3801 S. Meridan Ave.
Oklahoma City, OK
www.Browntool.com
800-587-3883
405-688-6888

----- Original Message -----
From: "Jean Poirier" <oxyport@globetrotter.net>
To: <murphy-rebel@dcsol.com>
Sent: Friday, December 12, 2003 11:30 AM
Subject: Re: [AVIS-NOTICE] Fw: flush avex rivet

I Jim
Do you have info about "Brown tool"?
Jean
Rebel 747R
----- Original Message -----
From: "goody" <goody@sover.net>
To: <murphy-rebel@dcsol.com>
Sent: Friday, December 05, 2003 10:58 AM
Subject: [AVIS-NOTICE] Fw: flush avex rivet

I have 120' countersinks with centering mandrels from Brown tool.
Jim
----- Original Message -----
From: <klehman@albedo.net>
To: <murphy-rebel@dcsol.com>
Sent: Thursday, December 04, 2003 12:43 PM
Subject: Re: flush avex rivet

Jean

120 degree countersinks are available in single flute and multi-flute
from tool suppliers but the ones that I have do not have a mandrel and
are not self centering. However a normal 118 degree drill bit will
finish the countersink a little better than just a 100 degree cutter

and

help you get a flush surface after you rivet.

120 degrees seems to be common for non aviation blind rivets including
avex, pop, and the structural Q rivets.

Ken

Wayne G. O'Shea wrote:

pretty

the

do

not

for

for

those

*-------------------------------------------------------------------------*

To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*
*-------------------------------------------------------------------------*

To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*
*-------------------------------------------------------------------------*

To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com

*-------------------------------------------------------------------------*



*-------------------------------------------------------------------------*
To unsubscribe from this list go to:
https://www.dcsol.com/public/code/html-subscribe.wcx
Archives located at https://rebel:builder@www.dcsol.com/default.htm
To contact the list admin, e-mail mike.davis@dcsol.com
*-------------------------------------------------------------------------*








-----------------------------------------------------------------
List archives located at: https://mail.dcsol.com/login
username "rebel" password "builder"
Unsubscribe: rebel-builders-unsubscribe@dcsol.com
List administrator: mike.davis@dcsol.com
-----------------------------------------------------------------